* commit '40fac1a66ccf61bdf3afb70c18a5db7791410b22': (220 commits)
Revert "tee: optee: interrupt an RPC when supplicant has been killed"
Revert "tee: optee: interrupt an RPC depend on shutdown flag"
arm64: dts: rockchip: rv1126bp-evb-v14: Adjust the matching voltage
media: rockchip: aiisp: delete one temp buffer to reduce memory
media: rockchip: isp: mp output buf notice to aiisp
media: rockchip: aiisp: modify for aiynr algo
rtc: rockchip: add ready flag for rtc setting time
soc: rockchip: cpuinfo: export chip unique id to userspace
media: rockchip: vpss: offline mode support auto unite output
drm/rockchip: vop2: Add "DIMMING_DATA" property for local dimming
media: rockchip: isp: aiisp switch for offline mode
media: rockchip: isp: aiisp switch for isp35
media: rockchip: isp: support aiisp yuv mode
input: touchscreen: gt1x: prefix global variables and functions with "gt1x_"
MALI: valhall: add gpu mem sysfs entry
drm/rockchip: Make the DRM panel as part of Rockchip DRM sub devices for panel loader protect
drm/rockchip: Pass struct rockchip_drm_sub_dev for &rockchip_drm_sub_dev.loader_protect()
pwm: rockchip: Add &rockchip_pwm_chip.oneshot_valid to indicate validity of configurations
pwm: rockchip: Add comments for why to add delay before disabling the dclk for PWM v4
input: touchscreen: hyn: reduce logs
...
Change-Id: I1b562efca0842173010b2506231d7200a5116e5a
we don't directly enable all evb board to support bt-sco cards
because it may take some i2s/pcm, which may use dma,
but dmas may limit.
so we just prepare this settings, then if any one who want to
support bt-sco, he/she can just add dts in board-level dts.
now, we just enable rk3568-evb1 and rk3566-evb1 just for example.
Diff in "rk3568-evb1-ddr4-v10.dts" is like this:
+&bt_sco {
+ status = "okay";
+};
+
+&bt_sound {
+ status = "okay";
+};
+
+&i2s3_2ch {
+ status = "okay";
+};
The default pcm/i2s setting is:
Format: PCM, dsp_a, MSB first, short sync, rising edge and delay 1 bclk.
rockchip soc: master; Bt controller: slave
Change-Id: I6668bfbb87e4b0ea71a661bbcf8248cbde77974e
Signed-off-by: Zou Dengming <marsow.zou@rock-chips.com>
The pcie supply design is (rk3566 evb2 example)
DC12V
-> VCC12V_PCIE(controlled by GPIO0_C2_H)
-> VCC3V3_PCIE(controlled by GPIO0_C2_H)
-> VCC5V0_SYS
-> VCC3V3_PI6C(controlled by GPIO0_C2_H)
The pci phy driver only want to enable or disable the VCC3V3_PCIE power.
Suggested from pcie owner to ignore the VCC12V_PCIE and VCC3V3_PI6C, so
the dts only need to add regulator node for VCC3V3_PCIE.
Most of time we keep the regulator name same as the hardware design, so
the dts node is
vcc3v3_pcie: gpio-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc3v3_pcie";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
enable-active-high;
gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
vin-supply = <&dc_12v>;
};
The regulator type is "regulator-fixed" since its voltage always be
3.3v, min and max should be 3300000 make the regulator has a voltage
value.
The regulator can be enabled or disabled by regulator_enable or
regulator_disable function, so make the GPIO0_B7 as "ena_pin" for the
regulator.
The regulator is supplied by DCIN_12V, so add the vin-supply.
Some boards need a delay before enabling trainning for power to be
stable from the measurement.
By measurement, 5ms is enough for power and refclk to be stable.
Change-Id: Iaf70abe9c9e06504af067dc0e3d60b775557c026
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
"system-status-level" property define only frequency level, not the
actual frequency. In dmc driver, it will switch from frequency level
to actual frequency base on available frequencies table which get
from ATF.
Change-Id: I489b671da5e56912d4f970d32174bdc8b1f86a08
Signed-off-by: YouMin Chen <cym@rock-chips.com>
supports-* stuff were used for rockchip platforms to speed up booting
if we know what exactly the host was used for. As we have upstreamed all
these with some very similar ways, now it's the time we migrate our dts
files to use new properties.
They were converted by:
sed -i "s/supports-emmc;/no-sdio;\n\tno-sd;/g" `grep supports-emmc -rl arch/*`
sed -i "s/supports-sd;/no-sdio;\n\tno-mmc;/g" `grep supports-sd -rl arch/*`
sed -i "s/supports-sdio;/no-sd;\n\tno-mmc;/g" `grep supports-sdio -rl arch/*`
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Change-Id: I33e5317ee5c7305803cf18ff4a370658abf555b0
Should not be zero ahead, otherwise the min voltage is interpreted
as a wrong value by regulator code.
Change-Id: Ia141583f411a54bf26cb88b3992687539f29fec8
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
