commit 93a8ba2a61 upstream.
Contrary to what was believed at the time, the ramp delay of 150us is not
plenty for the PU LDO with the default step time of 512 pulses of the 24MHz
clock. Measurements have shown that after enabling the LDO the voltage on
VDDPU_CAP jumps to ~750mV in the first step and after that the regulator
executes the normal ramp up as defined by the step size control.
This means it takes the regulator between 360us and 370us to ramp up to
the nominal 1.15V voltage for this power domain. With the old setting of
the ramp delay the power up of the PU GPC domain would happen in the middle
of the regulator ramp with the voltage being at around 900mV. Apparently
this was enough for most units to properly power up the peripherals in the
domain and execute the reset. Some units however, fail to power up properly,
especially when the chip is at a low temperature. In that case any access
to the GPU registers would yield an incorrect result with no way to recover
from this situation.
Change the ramp delay to 380us to cover the measured ramp up time with a
bit of additional slack.
Fixes: 40130d327f ("ARM: dts: imx6qdl: Allow disabling the PU regulator, add a enable ramp delay")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 552ca27929 upstream.
Move the power domain to its actual user. This keeps the power domain
enabled even when the USB host is runtime suspended. This is necessary
to detect any downstream events, like device attach.
Fixes: 02f8eb40ef ("ARM: dts: imx7s: Add power domain for imx7d HSIC")
Suggested-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 57f718aa4b ]
The red LED on the Raspberry Pi 3 B Plus is the power LED.
So fix the GPIO line name accordingly.
Fixes: 71c0cd2283 ("ARM: dts: bcm2837: Add Raspberry Pi 3 B+")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fd26fd027 ]
The GPIOs 46 & 47 are already used for a I2C interface to a SMPS.
So fix the GPIO line names accordingly.
Fixes: a54fe8a6cf ("ARM: dts: add Raspberry Pi Compute Module 3 and IO board")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c663e5e5b ]
The GPIOs 30 to 39 are connected to the Cypress CYW43438 (Wifi/BT).
So fix the GPIO line names accordingly.
Fixes: 2c7c040c73 ("ARM: dts: bcm2835: Add Raspberry Pi Zero W")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5f5c579a34 ]
Fix names of extra pingroup node and property for gpio bus recovery.
Without the change i2c2 is not functional.
Fixes: 56f0df6b6b ("ARM: dts: imx*(colibri|apalis): add missing recovery modes to i2c")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d397a1277 ]
Commit f3e7dae323 ("ARM: dts: imx6qdl: add enet_out clk
support") added another item to the list of clocks for the fec
device. As imx6dl-eckelmann-ci4x10.dts only overwrites clocks,
but not clock-names this resulted in an inconsistency with
clocks having one item more than clock-names.
Also overwrite clock-names with the same value as in
imx6qdl.dtsi. This is a no-op today, but prevents similar
inconsistencies if the soc file will be changed in a similar way
in the future.
Signed-off-by: Thorsten Scherer <t.scherer@eckelmann.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f3e7dae323 ("ARM: dts: imx6qdl: add enet_out clk support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 01a850ee61 ]
The F1C100 series of SoCs actually have their watchdog IP being
compatible with the newer Allwinner generation, not the older one.
The currently described sun4i-a10-wdt actually does not work, neither
the watchdog functionality (just never fires), nor the reset part
(reboot hangs).
Replace the compatible string with the one used by the newer generation.
Verified to work with both the watchdog and reboot functionality on a
LicheePi Nano.
Also add the missing interrupt line and clock source, to make it binding
compliant.
Fixes: 4ba16d17ef ("ARM: dts: suniv: add initial DTSI file for F1C100s")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220317162349.739636-4-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45974e4276 ]
The correct spelling for the property is gpios. Otherwise, the regulator
will neither reserve nor control any GPIOs. Thus, any SD/MMC card which
can use UHS-I modes will fail.
Fixes: c2e4987e0e ("ARM: dts: imx6ull: add Toradex Colibri iMX6ULL support")
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46ff3df872 ]
The pinout of the OMAP35 and DM37 variants of the SOM-LV are the
same, but the macros which define the pinmuxing are different
between OMAP3530 and DM3730. The pinmuxing was correct for
for the DM3730, but wrong for the OMAP3530. Since the boot loader
was correctly pin-muxing the pins, this was not obvious. As the
bootloader not guaranteed to pinmux all the pins any more, this
causes an issue, so the pinmux needs to be moved from a common
file to their respective board files.
Fixes: f8a2e3ff71 ("ARM: dts: Add minimal support for LogicPD OMAP35xx SOM-LV devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220303171818.11060-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 942da3af32 ]
The bootloader for the AM3517 has previously done much of the pin
muxing, but as the bootloader is moving more and more to a model
based on the device tree, it may no longer automatically mux the
pins, so it is necessary to add the pinmuxing to the Linux device
trees so the respective peripherals can remain functional.
Fixes: 6ed1d79975 ("ARM: dts: am3517-evm: Add support for UI board and Audio")
Signed-off-by: Adam Ford <aford173@gmail.com>
Message-Id: <20220226214820.747847-1-aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fa51e1dc4b ]
On a custom carrier board with a i.MX6Q Apalis SoM, the sgtl5000 codec
on the SoM is often not detected and the following error message is
seen when the sgtl5000 driver tries to read the ID register:
sgtl5000 1-000a: Error reading chip id -6
The reason for the error is that the MCLK clock is not provided
early enough.
Fix the problem by describing the MCLK pinctrl inside the codec
node instead of placing it inside the audmux pinctrl group.
With this change applied the sgtl5000 is always detected on every boot.
Fixes: 693e3ffaae ("ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0092c25b54 ]
This patch fixes the tristate configuration for i2c3 function assigned
to the dtf pins on the Tamonten Tegra20 SoM.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 618682b350 ]
This patch fixes the kernel warning
"cacheinfo: Unable to detect cache hierarchy for CPU 0"
for the bcm2711 on newer kernel versions.
Signed-off-by: Richard Schleich <rs@noreya.tech>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
[florian: Align and remove comments matching property values]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4cb7df64c7 ]
The audio_mclk_root_clk was added as a gate with the CCGR121 (0x4790),
but according to the reference manual, there is no such gate. Moreover,
the consumer driver of the mentioned clock might gate it and leave
the ECSPI2 (the true owner of that gate) hanging. So lets use the
audio_mclk_post_div, which is the parent.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bdf8762da2 ]
This patch fixes the kernel warning
"cacheinfo: Unable to detect cache hierarchy for CPU 0"
for the bcm2837 on newer kernel versions.
Signed-off-by: Richard Schleich <rs@noreya.tech>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
[florian: Align and remove comments matching property values]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f6edb6bcb ]
Requesting quad mode for the FMC resulted in an error:
&fmc {
status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_fwqspi_default>'
[ 0.742963] aspeed-g6-pinctrl 1e6e2000.syscon:pinctrl: invalid function FWQSPID in map table

This is because the quad mode pins are a group of pins, not a function.
After applying this patch we can request the pins and the QSPI data
lines are muxed:
# cat /sys/kernel/debug/pinctrl/1e6e2000.syscon\:pinctrl-aspeed-g6-pinctrl/pinmux-pins |grep 1e620000.spi
pin 196 (AE12): device 1e620000.spi function FWSPID group FWQSPID
pin 197 (AF12): device 1e620000.spi function FWSPID group FWQSPID
pin 240 (Y1): device 1e620000.spi function FWSPID group FWQSPID
pin 241 (Y2): device 1e620000.spi function FWSPID group FWQSPID
pin 242 (Y3): device 1e620000.spi function FWSPID group FWQSPID
pin 243 (Y4): device 1e620000.spi function FWSPID group FWQSPID
Fixes: f510f04c8c ("ARM: dts: aspeed: Add AST2600 pinmux nodes")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20220304011010.974863-1-joel@jms.id.au
Link: https://lore.kernel.org/r/20220304011010.974863-1-joel@jms.id.au'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 515415d316 ]
While the HVS has the same context memory size in the BCM2711 than in
the previous SoCs, the range allocated to the registers doubled and it
now takes 16k + 16k, compared to 8k + 16k before.
The KMS driver will use the whole context RAM though, eventually
resulting in a pointer dereference error when we access the higher half
of the context memory since it hasn't been mapped.
Fixes: 4564363351 ("ARM: dts: bcm2711: Enable the display pipeline")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d3b01e0d4 ]
Move the eDP panel on Venice 2 and Nyan boards into the corresponding
AUX bus device tree node. This allows us to avoid a nasty circular
dependency that would otherwise be created between the DPAUX and panel
nodes via the DDC/I2C phandle.
Fixes: eb481f9ac9 ("ARM: tegra: add Acer Chromebook 13 device tree")
Fixes: 59fe02cb07 ("ARM: tegra: Add DTS for the nyan-blaze board")
Fixes: 40e231c770 ("ARM: tegra: Enable eDP for Venice2")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8840f5460a ]
Devkit8000 board seems to always used 32k_counter as clocksource.
Restore this behavior.
If clocksource is back to 32k_counter, timer12 is now the clockevent
source (as before) and timer2 is not longer needed here.
This commit fixes the same issue observed with commit 23885389db
("ARM: dts: Fix timer regression for beagleboard revision c") when sleep
is blocked until hitting keys over serial console.
Fixes: aba1ad05da ("clocksource/drivers/timer-ti-dm: Add clockevent and clocksource support")
Fixes: e428e250fd ("ARM: dts: Configure system timers for omap3")
Signed-off-by: Anthoine Bourgeois <anthoine.bourgeois@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d58c5e21a ]
The correct property name is 'assigned-clock-parents', not
'assigned-clocks-parents'. Though if the platform works with the typo, one
has to wonder if the property is even needed.
Signed-off-by: Rob Herring <robh@kernel.org>
Fixes: 8b8c7d97e2 ("ARM: dts: imx7ulp: Add wdog1 node")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3375aa7713 ]
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8b-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8b-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml bindings.
Fixes: b02d6e73f5 ("ARM: dts: meson8b: use stable UART bindings with correct gate clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211227180026.4068352-4-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 57007bfb54 ]
The dt-bindings for the UART controller only allow the following values
for Meson8 SoCs:
- "amlogic,meson8-uart", "amlogic,meson-ao-uart"
- "amlogic,meson8-uart"
Use the correct fallback compatible string "amlogic,meson-ao-uart" for
AO UART. Drop the "amlogic,meson-uart" compatible string from the EE
domain UART controllers.
Also update the order of the clocks to match the order defined in the
yaml schema.
Fixes: 6ca7750205 ("ARM: dts: meson8: use stable UART bindings with correct gate clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20211227180026.4068352-3-martin.blumenstingl@googlemail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
