Pull PCI updates from Bjorn Helgaas:
"PCI changes for the v3.14 merge window:
Resource management
- Change pci_bus_region addresses to dma_addr_t (Bjorn Helgaas)
- Support 64-bit AGP BARs (Bjorn Helgaas, Yinghai Lu)
- Add pci_bus_address() to get bus address of a BAR (Bjorn Helgaas)
- Use pci_resource_start() for CPU address of AGP BARs (Bjorn Helgaas)
- Enforce bus address limits in resource allocation (Yinghai Lu)
- Allocate 64-bit BARs above 4G when possible (Yinghai Lu)
- Convert pcibios_resource_to_bus() to take pci_bus, not pci_dev (Yinghai Lu)
PCI device hotplug
- Major rescan/remove locking update (Rafael J. Wysocki)
- Make ioapic builtin only (not modular) (Yinghai Lu)
- Fix release/free issues (Yinghai Lu)
- Clean up pciehp (Bjorn Helgaas)
- Announce pciehp slot info during enumeration (Bjorn Helgaas)
MSI
- Add pci_msi_vec_count(), pci_msix_vec_count() (Alexander Gordeev)
- Add pci_enable_msi_range(), pci_enable_msix_range() (Alexander Gordeev)
- Deprecate "tri-state" interfaces: fail/success/fail+info (Alexander Gordeev)
- Export MSI mode using attributes, not kobjects (Greg Kroah-Hartman)
- Drop "irq" param from *_restore_msi_irqs() (DuanZhenzhong)
SR-IOV
- Clear NumVFs when disabling SR-IOV in sriov_init() (ethan.zhao)
Virtualization
- Add support for save/restore of extended capabilities (Alex Williamson)
- Add Virtual Channel to save/restore support (Alex Williamson)
- Never treat a VF as a multifunction device (Alex Williamson)
- Add pci_try_reset_function(), et al (Alex Williamson)
AER
- Ignore non-PCIe error sources (Betty Dall)
- Support ACPI HEST error sources for domains other than 0 (Betty Dall)
- Consolidate HEST error source parsers (Bjorn Helgaas)
- Add a TLP header print helper (Borislav Petkov)
Freescale i.MX6
- Remove unnecessary code (Fabio Estevam)
- Make reset-gpio optional (Marek Vasut)
- Report "link up" only after link training completes (Marek Vasut)
- Start link in Gen1 before negotiating for Gen2 mode (Marek Vasut)
- Fix PCIe startup code (Richard Zhu)
Marvell MVEBU
- Remove duplicate of_clk_get_by_name() call (Andrew Lunn)
- Drop writes to bridge Secondary Status register (Jason Gunthorpe)
- Obey bridge PCI_COMMAND_MEM and PCI_COMMAND_IO bits (Jason Gunthorpe)
- Support a bridge with no IO port window (Jason Gunthorpe)
- Use max_t() instead of max(resource_size_t,) (Jingoo Han)
- Remove redundant of_match_ptr (Sachin Kamat)
- Call pci_ioremap_io() at startup instead of dynamically (Thomas Petazzoni)
NVIDIA Tegra
- Disable Gen2 for Tegra20 and Tegra30 (Eric Brower)
Renesas R-Car
- Add runtime PM support (Valentine Barshak)
- Fix rcar_pci_probe() return value check (Wei Yongjun)
Synopsys DesignWare
- Fix crash in dw_msi_teardown_irq() (Bjørn Erik Nilsen)
- Remove redundant call to pci_write_config_word() (Bjørn Erik Nilsen)
- Fix missing MSI IRQs (Harro Haan)
- Add dw_pcie prefix before cfg_read/write (Pratyush Anand)
- Fix I/O transfers by using CPU (not realio) address (Pratyush Anand)
- Whitespace cleanup (Jingoo Han)
EISA
- Call put_device() if device_register() fails (Levente Kurusa)
- Revert EISA initialization breakage ((Bjorn Helgaas)
Miscellaneous
- Remove unused code, including PCIe 3.0 interfaces (Stephen Hemminger)
- Prevent bus conflicts while checking for bridge apertures (Bjorn Helgaas)
- Stop clearing bridge Secondary Status when setting up I/O aperture (Bjorn Helgaas)
- Use dev_is_pci() to identify PCI devices (Yijing Wang)
- Deprecate DEFINE_PCI_DEVICE_TABLE (Joe Perches)
- Update documentation 00-INDEX (Erik Ekman)"
* tag 'pci-v3.14-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (119 commits)
Revert "EISA: Initialize device before its resources"
Revert "EISA: Log device resources in dmesg"
vfio-pci: Use pci "try" reset interface
PCI: Check parent kobject in pci_destroy_dev()
xen/pcifront: Use global PCI rescan-remove locking
powerpc/eeh: Use global PCI rescan-remove locking
PCI: Fix pci_check_and_unmask_intx() comment typos
PCI: Add pci_try_reset_function(), pci_try_reset_slot(), pci_try_reset_bus()
MPT / PCI: Use pci_stop_and_remove_bus_device_locked()
platform / x86: Use global PCI rescan-remove locking
PCI: hotplug: Use global PCI rescan-remove locking
pcmcia: Use global PCI rescan-remove locking
ACPI / hotplug / PCI: Use global PCI rescan-remove locking
ACPI / PCI: Use global PCI rescan-remove locking in PCI root hotplug
PCI: Add global pci_lock_rescan_remove()
PCI: Cleanup pci.h whitespace
PCI: Reorder so actual code comes before stubs
PCI/AER: Support ACPI HEST AER error sources for PCI domains other than 0
ACPICA: Add helper macros to extract bus/segment numbers from HEST table.
PCI: Make local functions static
...
Pull tracing updates from Steven Rostedt:
"This pull request has a new feature to ftrace, namely the trace event
triggers by Tom Zanussi. A trigger is a way to enable an action when
an event is hit. The actions are:
o trace on/off - enable or disable tracing
o snapshot - save the current trace buffer in the snapshot
o stacktrace - dump the current stack trace to the ringbuffer
o enable/disable events - enable or disable another event
Namhyung Kim added updates to the tracing uprobes code. Having the
uprobes add support for fetch methods.
The rest are various bug fixes with the new code, and minor ones for
the old code"
* tag 'trace-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (38 commits)
tracing: Fix buggered tee(2) on tracing_pipe
tracing: Have trace buffer point back to trace_array
ftrace: Fix synchronization location disabling and freeing ftrace_ops
ftrace: Have function graph only trace based on global_ops filters
ftrace: Synchronize setting function_trace_op with ftrace_trace_function
tracing: Show available event triggers when no trigger is set
tracing: Consolidate event trigger code
tracing: Fix counter for traceon/off event triggers
tracing: Remove double-underscore naming in syscall trigger invocations
tracing/kprobes: Add trace event trigger invocations
tracing/probes: Fix build break on !CONFIG_KPROBE_EVENT
tracing/uprobes: Add @+file_offset fetch method
uprobes: Allocate ->utask before handler_chain() for tracing handlers
tracing/uprobes: Add support for full argument access methods
tracing/uprobes: Fetch args before reserving a ring buffer
tracing/uprobes: Pass 'is_return' to traceprobe_parse_probe_arg()
tracing/probes: Implement 'memory' fetch method for uprobes
tracing/probes: Add fetch{,_size} member into deref fetch method
tracing/probes: Move 'symbol' fetch method to kprobes
tracing/probes: Implement 'stack' fetch method for uprobes
...
Merge first patch-bomb from Andrew Morton:
- a couple of misc things
- inotify/fsnotify work from Jan
- ocfs2 updates (partial)
- about half of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (117 commits)
mm/migrate: remove unused function, fail_migrate_page()
mm/migrate: remove putback_lru_pages, fix comment on putback_movable_pages
mm/migrate: correct failure handling if !hugepage_migration_support()
mm/migrate: add comment about permanent failure path
mm, page_alloc: warn for non-blockable __GFP_NOFAIL allocation failure
mm: compaction: reset scanner positions immediately when they meet
mm: compaction: do not mark unmovable pageblocks as skipped in async compaction
mm: compaction: detect when scanners meet in isolate_freepages
mm: compaction: reset cached scanner pfn's before reading them
mm: compaction: encapsulate defer reset logic
mm: compaction: trace compaction begin and end
memcg, oom: lock mem_cgroup_print_oom_info
sched: add tracepoints related to NUMA task migration
mm: numa: do not automatically migrate KSM pages
mm: numa: trace tasks that fail migration due to rate limiting
mm: numa: limit scope of lock for NUMA migrate rate limiting
mm: numa: make NUMA-migrate related functions static
lib/show_mem.c: show num_poisoned_pages when oom
mm/hwpoison: add '#' to hwpoison_inject
mm/memblock: use WARN_ONCE when MAX_NUMNODES passed as input parameter
...
Pull libata updates from Tejun Heo:
"Support for some new embedded controllers.
A couple late (<= a week) fixes have stable cc'd and one patch ("SATA:
MV: Add support for the optional PHYs") got committed yesterday
because otherwise the resulting kernel would fail boot on an embedded
board due to interdependent changes in its platform tree.
Other than that, nothing too noteworthy"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
SATA: MV: Add support for the optional PHYs
sata-highbank: Remove unnecessary ahci_platform.h include
libata: disable LPM for some WD SATA-I devices
ARM: mvebu: update the SATA compatible string for Armada 370/XP
ata: sata_mv: fix disk hotplug for Armada 370/XP SoCs
ata: sata_mv: introduce compatible string "marvell, armada-370-sata"
ata: pata_samsung_cf: Remove unused macros
ata: pata_samsung_cf: Use devm_ioremap_resource()
ata: pata_samsung_cf: Merge pata_samsung_cf.h into pata_samsung_cf.c
ata: pata_samsung_cf: Move plat/regs-ata.h to drivers/ata
drivers: ata: Mark the function as static in libahci.c
drivers: ata: Mark the function ahci_init_interrupts() as static in ahci.c
ahci: imx: fix the error handling in imx_ahci_probe()
ahci: imx: ahci_imx_softreset() can be static
ahci: imx: Add i.MX53 support
ahci: imx: Pull out the clock enable/disable calls
libata, dt: Document sata_rcar bindings
sata_rcar: Add R-Car Gen2 SATA PHY support
ahci: mcp89: enter AHCI mode under Apple BIOS emulation
ata: libata-eh: Remove unnecessary snprintf arithmetic
Pull cgroup updates from Tejun Heo:
"The bulk of changes are cleanups and preparations for the upcoming
kernfs conversion.
- cgroup_event mechanism which is and will be used only by memcg is
moved to memcg.
- pidlist handling is updated so that it can be served by seq_file.
Also, the list is not sorted if sane_behavior. cgroup
documentation explicitly states that the file is not sorted but it
has been for quite some time.
- All cgroup file handling now happens on top of seq_file. This is
to prepare for kernfs conversion. In addition, all operations are
restructured so that they map 1-1 to kernfs operations.
- Other cleanups and low-pri fixes"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (40 commits)
cgroup: trivial style updates
cgroup: remove stray references to css_id
doc: cgroups: Fix typo in doc/cgroups
cgroup: fix fail path in cgroup_load_subsys()
cgroup: fix missing unlock on error in cgroup_load_subsys()
cgroup: remove for_each_root_subsys()
cgroup: implement for_each_css()
cgroup: factor out cgroup_subsys_state creation into create_css()
cgroup: combine css handling loops in cgroup_create()
cgroup: reorder operations in cgroup_create()
cgroup: make for_each_subsys() useable under cgroup_root_mutex
cgroup: css iterations and css_from_dir() are safe under cgroup_mutex
cgroup: unify pidlist and other file handling
cgroup: replace cftype->read_seq_string() with cftype->seq_show()
cgroup: attach cgroup_open_file to all cgroup files
cgroup: generalize cgroup_pidlist_open_file
cgroup: unify read path so that seq_file is always used
cgroup: unify cgroup_write_X64() and cgroup_write_string()
cgroup: remove cftype->read(), ->read_map() and ->write()
hugetlb_cgroup: convert away from cftype->read()
...
Currently there are several functions to manipulate the deferred
compaction state variables. The remaining case where the variables are
touched directly is when a successful allocation occurs in direct
compaction, or is expected to be successful in the future by kswapd.
Here, the lowest order that is expected to fail is updated, and in the
case of successful allocation, the deferred status and counter is reset
completely.
Create a new function compaction_defer_reset() to encapsulate this
functionality and make it easier to understand the code. No functional
change.
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NUMA migrate rate limiting protects a migration counter and window using
a lock but in some cases this can be a contended lock. It is not
critical that the number of pages be perfect, lost updates are
acceptable. Reduce the importance of this lock.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Cc: Alex Thorlton <athorlton@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce memblock memory allocation APIs which allow to support PAE or
LPAE extension on 32 bits archs where the physical memory start address
can be beyond 4GB. In such cases, existing bootmem APIs which operate
on 32 bit addresses won't work and needs memblock layer which operates
on 64 bit addresses.
So we add equivalent APIs so that we can replace usage of bootmem with
memblock interfaces. Architectures already converted to NO_BOOTMEM use
these new memblock interfaces. The architectures which are still not
converted to NO_BOOTMEM continue to function as is because we still
maintain the fal lback option of bootmem back-end supporting these new
interfaces. So no functional change as such.
In long run, once all the architectures moves to NO_BOOTMEM, we can get
rid of bootmem layer completely. This is one step to remove the core
code dependency with bootmem and also gives path for architectures to
move away from bootmem.
The proposed interface will became active if both CONFIG_HAVE_MEMBLOCK
and CONFIG_NO_BOOTMEM are specified by arch. In case
!CONFIG_NO_BOOTMEM, the memblock() wrappers will fallback to the
existing bootmem apis so that arch's not converted to NO_BOOTMEM
continue to work as is.
The meaning of MEMBLOCK_ALLOC_ACCESSIBLE and MEMBLOCK_ALLOC_ANYWHERE
is kept same.
[akpm@linux-foundation.org: s/depricated/deprecated/]
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
while_each_thread() and next_thread() should die, almost every lockless
usage is wrong.
1. Unless g == current, the lockless while_each_thread() is not safe.
while_each_thread(g, t) can loop forever if g exits, next_thread()
can't reach the unhashed thread in this case. Note that this can
happen even if g is the group leader, it can exec.
2. Even if while_each_thread() itself was correct, people often use
it wrongly.
It was never safe to just take rcu_read_lock() and loop unless
you verify that pid_alive(g) == T, even the first next_thread()
can point to the already freed/reused memory.
This patch adds signal_struct->thread_head and task->thread_node to
create the normal rcu-safe list with the stable head. The new
for_each_thread(g, t) helper is always safe under rcu_read_lock() as
long as this task_struct can't go away.
Note: of course it is ugly to have both task_struct->thread_node and the
old task_struct->thread_group, we will kill it later, after we change
the users of while_each_thread() to use for_each_thread().
Perhaps we can kill it even before we convert all users, we can
reimplement next_thread(t) using the new thread_head/thread_node. But
we can't do this right now because this will lead to subtle behavioural
changes. For example, do/while_each_thread() always sees at least one
task, while for_each_thread() can do nothing if the whole thread group
has died. Or thread_group_empty(), currently its semantics is not clear
unless thread_group_leader(p) and we need to audit the callers before we
can change it.
So this patch adds the new interface which has to coexist with the old
one for some time, hopefully the next changes will be more or less
straightforward and the old one will go away soon.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Sergey Dyasly <dserrg@gmail.com>
Tested-by: Sergey Dyasly <dserrg@gmail.com>
Reviewed-by: Sameer Nanda <snanda@chromium.org>
Acked-by: David Rientjes <rientjes@google.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mandeep Singh Baines <msb@chromium.org>
Cc: "Ma, Xindong" <xindong.ma@intel.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: "Tu, Xiaobing" <xiaobing.tu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, we have an infrastructure in rmap_walk() to handle difference from
variants of rmap traversing functions.
So, just use it in page_referenced().
In this patch, I change following things.
1. remove some variants of rmap traversing functions.
cf> page_referenced_ksm, page_referenced_anon,
page_referenced_file
2. introduce new struct page_referenced_arg and pass it to
page_referenced_one(), main function of rmap_walk, in order to count
reference, to store vm_flags and to check finish condition.
3. mechanical change to use rmap_walk() in page_referenced().
[liwanp@linux.vnet.ibm.com: fix BUG at rmap_walk]
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now, we have an infrastructure in rmap_walk() to handle difference from
variants of rmap traversing functions.
So, just use it in try_to_munlock().
In this patch, I change following things.
1. remove some variants of rmap traversing functions.
cf> try_to_unmap_ksm, try_to_unmap_anon, try_to_unmap_file
2. mechanical change to use rmap_walk() in try_to_munlock().
3. copy and paste comments.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of common parts in traversing functions, but there are
also a little of uncommon parts in it. By assigning proper function
pointer on each rmap_walker_control, we can handle these difference
correctly.
Following are differences we should handle.
1. difference of lock function in anon mapping case
2. nonlinear handling in file mapping case
3. prechecked condition:
checking memcg in page_referenced(),
checking VM_SHARE in page_mkclean()
checking temporary vma in try_to_unmap()
4. exit condition:
checking page_mapped() in try_to_unmap()
So, in this patch, I introduce 4 function pointers to handle above
differences.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In each rmap traverse case, there is some difference so that we need
function pointers and arguments to them in order to handle these
For this purpose, struct rmap_walk_control is introduced in this patch,
and will be extended in following patch. Introducing and extending are
separate, because it clarify changes.
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux kernel cannot migrate pages used by the kernel. As a result,
hotpluggable memory used by the kernel won't be able to be hot-removed.
To solve this problem, the basic idea is to prevent memblock from
allocating hotpluggable memory for the kernel at early time, and arrange
all hotpluggable memory in ACPI SRAT(System Resource Affinity Table) as
ZONE_MOVABLE when initializing zones.
In the previous patches, we have marked hotpluggable memory regions with
MEMBLOCK_HOTPLUG flag in memblock.memory.
In this patch, we make memblock skip these hotpluggable memory regions
in the default top-down allocation function if movable_node boot option
is specified.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Chen Tang <imtangchen@gmail.com>
Cc: Gong Chen <gong.chen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Liu Jiang <jiang.liu@huawei.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vasilis Liaskovitis <vasilis.liaskovitis@profitbricks.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In find_hotpluggable_memory, once we find out a memory region which is
hotpluggable, we want to mark them in memblock.memory. So that we could
control memblock allocator not to allocte hotpluggable memory for the
kernel later.
To achieve this goal, we introduce MEMBLOCK_HOTPLUG flag to indicate the
hotpluggable memory regions in memblock and a function
memblock_mark_hotplug() to mark hotpluggable memory if we find one.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Tang Chen <tangchen@cn.fujitsu.com>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Rafael J . Wysocki" <rjw@sisk.pl>
Cc: Chen Tang <imtangchen@gmail.com>
Cc: Gong Chen <gong.chen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Liu Jiang <jiang.liu@huawei.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Taku Izumi <izumi.taku@jp.fujitsu.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Toshi Kani <toshi.kani@hp.com>
Cc: Vasilis Liaskovitis <vasilis.liaskovitis@profitbricks.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Wen Congyang <wency@cn.fujitsu.com>
Cc: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some applications that run on HPC clusters are designed around the
availability of RAM and the overcommit ratio is fine tuned to get the
maximum usage of memory without swapping. With growing memory, the
1%-of-all-RAM grain provided by overcommit_ratio has become too coarse
for these workload (on a 2TB machine it represents no less than 20GB).
This patch adds the new overcommit_kbytes sysctl variable that allow a
much finer grain.
[akpm@linux-foundation.org: coding-style fixes]
[akpm@linux-foundation.org: fix nommu build]
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4b59e6c473 ("mm, show_mem: suppress page counts in
non-blockable contexts") introduced SHOW_MEM_FILTER_PAGE_COUNT to
suppress PFN walks on large memory machines. Commit c78e93630d ("mm:
do not walk all of system memory during show_mem") avoided a PFN walk in
the generic show_mem helper which removes the requirement for
SHOW_MEM_FILTER_PAGE_COUNT in that case.
This patch removes PFN walkers from the arch-specific implementations
that report on a per-node or per-zone granularity. ARM and unicore32
still do a PFN walk as they report memory usage on each bank which is a
much finer granularity where the debugging information may still be of
use. As the remaining arches doing PFN walks have relatively small
amounts of memory, this patch simply removes SHOW_MEM_FILTER_PAGE_COUNT.
[akpm@linux-foundation.org: fix parisc]
Signed-off-by: Mel Gorman <mgorman@suse.de>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: James Bottomley <jejb@parisc-linux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mempolicies only exist for CONFIG_NUMA configurations. Therefore, a
certain class of functions are unneeded in configurations where
CONFIG_NUMA is disabled such as functions that duplicate existing
mempolicies, lookup existing policies, set certain mempolicy traits, or
test mempolicies for certain attributes.
Remove the unneeded functions so that any future callers get a compile-
time error and protect their code with CONFIG_NUMA as required.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If DEBUG_SPINLOCK and DEBUG_LOCK_ALLOC are enabled spinlock_t on x86_64
is 72 bytes. For page->ptl they will be allocated from kmalloc-96 slab,
so we loose 24 on each. An average system can easily allocate few tens
thousands of page->ptl and overhead is significant.
Let's create a separate slab for page->ptl allocation to solve this.
To make sure that it really works this time, some numbers from my test
machine (just booted, no load):
Before:
# grep '^\(kmalloc-96\|page->ptl\)' /proc/slabinfo
kmalloc-96 31987 32190 128 30 1 : tunables 120 60 8 : slabdata 1073 1073 92
After:
# grep '^\(kmalloc-96\|page->ptl\)' /proc/slabinfo
page->ptl 27516 28143 72 53 1 : tunables 120 60 8 : slabdata 531 531 9
kmalloc-96 3853 5280 128 30 1 : tunables 120 60 8 : slabdata 176 176 0
Note that the patch is useful not only for debug case, but also for
PREEMPT_RT, where spinlock_t is always bloated.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yasuaki Ishimatsu reported memory hot-add spent more than 5 _hours_ on
9TB memory machine since onlining memory sections is too slow. And we
found out setup_zone_migrate_reserve spent >90% of the time.
The problem is, setup_zone_migrate_reserve scans all pageblocks
unconditionally, but it is only necessary if the number of reserved
block was reduced (i.e. memory hot remove).
Moreover, maximum MIGRATE_RESERVE per zone is currently 2. It means
that the number of reserved pageblocks is almost always unchanged.
This patch adds zone->nr_migrate_reserve_block to maintain the number of
MIGRATE_RESERVE pageblocks and it reduces the overhead of
setup_zone_migrate_reserve dramatically. The following table shows time
of onlining a memory section.
Amount of memory | 128GB | 192GB | 256GB|
---------------------------------------------
linux-3.12 | 23.9 | 31.4 | 44.5 |
This patch | 8.3 | 8.3 | 8.6 |
Mel's proposal patch | 10.9 | 19.2 | 31.3 |
---------------------------------------------
(millisecond)
128GB : 4 nodes and each node has 32GB of memory
192GB : 6 nodes and each node has 32GB of memory
256GB : 8 nodes and each node has 32GB of memory
(*1) Mel proposed his idea by the following threads.
https://lkml.org/lkml/2013/10/30/272
[akpm@linux-foundation.org: tweak comment]
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reported-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Tested-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This skips the _mapcount mangling for slab and hugetlbfs pages.
The main trouble in doing this is to guarantee that PageSlab and
PageHeadHuge remains constant for all get_page/put_page run on the tail
of slab or hugetlbfs compound pages. Otherwise if they're set during
get_page but not set during put_page, the _mapcount of the tail page
would underflow.
PageHeadHuge will remain true until the compound page is released and
enters the buddy allocator so it won't risk to change even if the tail
page is the last reference left on the page.
PG_slab instead is cleared before the slab frees the head page with
put_page, so if the tail pin is released after the slab freed the page,
we would have a problem. But in the slab case the tail pin cannot be
the last reference left on the page. This is because the slab code is
free to reuse the compound page after a kfree/kmem_cache_free without
having to check if there's any tail pin left. In turn all tail pins
must be always released while the head is still pinned by the slab code
and so we know PG_slab will be still set too.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we don't clobber page_tail->first_page during split_huge_page,
so compound_trans_head can be set to compound_head without adverse
effects, and this mostly optimizes away a smp_rmb.
It looks worthwhile to keep around the implementation that doesn't relay
on page_tail->first_page not to be clobbered, because it would be
necessary if we'll decide to enforce page->private to zero at all times
whenever PG_private is not set, also for anonymous pages. For anonymous
pages enforcing such an invariant doesn't matter as anonymous pages
don't use page->private so we can get away with this microoptimization.
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Khalid Aziz <khalid.aziz@oracle.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Johannes Weiner <jweiner@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Dave Jiang reported that he was seeing oopses when running NUMA systems
and default_hugepagesz=1G. I traced the issue down to
migrate_page_copy() trying to use the same code for hugetlb pages and
transparent hugepages. It should not have been trying to pass thp pages
in there.
So, add some VM_BUG_ON()s for the next hapless VM developer that tries
the same thing.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
{,set}page_address() are macros if WANT_PAGE_VIRTUAL. If
!WANT_PAGE_VIRTUAL, they're plain C functions.
If someone calls them with a void *, this pointer is auto-converted to
struct page * if !WANT_PAGE_VIRTUAL, but causes a build failure on
architectures using WANT_PAGE_VIRTUAL (arc, m68k and sparc64):
drivers/md/bcache/bset.c: In function `__btree_sort':
drivers/md/bcache/bset.c:1190: warning: dereferencing `void *' pointer
drivers/md/bcache/bset.c:1190: error: request for member `virtual' in something not a structure or union
Convert them to static inline functions to fix this. There are already
plenty of users of struct page members inside <linux/mm.h>, so there's
no reason to keep them as macros.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently fsnotify framework creates one event structure for each
notification event and links this event into all interested notification
groups. This is done so that we save memory when several notification
groups are interested in the event. However the need for event
structure shared between inotify & fanotify bloats the event structure
so the result is often higher memory consumption.
Another problem is that fsnotify framework keeps path references with
outstanding events so that fanotify can return open file descriptors
with its events. This has the undesirable effect that filesystem cannot
be unmounted while there are outstanding events - a regression for
inotify compared to a situation before it was converted to fsnotify
framework. For fanotify this problem is hard to avoid and users of
fanotify should kind of expect this behavior when they ask for file
descriptors from notified files.
This patch changes fsnotify and its users to create separate event
structure for each group. This allows for much simpler code (~400 lines
removed by this patch) and also smaller event structures. For example
on 64-bit system original struct fsnotify_event consumes 120 bytes, plus
additional space for file name, additional 24 bytes for second and each
subsequent group linking the event, and additional 32 bytes for each
inotify group for private data. After the conversion inotify event
consumes 48 bytes plus space for file name which is considerably less
memory unless file names are long and there are several groups
interested in the events (both of which are uncommon). Fanotify event
fits in 56 bytes after the conversion (fanotify doesn't care about file
names so its events don't have to have it allocated). A win unless
there are four or more fanotify groups interested in the event.
The conversion also solves the problem with unmount when only inotify is
used as we don't have to grab path references for inotify events.
[hughd@google.com: fanotify: fix corruption preventing startup]
Signed-off-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Eric Paris <eparis@parisplace.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Record actively mapped pages and provide an api for asserting a given
page is dma inactive before execution proceeds. Placing
debug_dma_assert_idle() in cow_user_page() flagged the violation of the
dma-api in the NET_DMA implementation (see commit 7787380336 "net_dma:
mark broken").
The implementation includes the capability to count, in a limited way,
repeat mappings of the same page that occur without an intervening
unmap. This 'overlap' counter is limited to the few bits of tag space
in a radix tree. This mechanism is added to mitigate false negative
cases where, for example, a page is dma mapped twice and
debug_dma_assert_idle() is called after the page is un-mapped once.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull battery updates from Dmitry Eremin-Solenikov:
"I'm picking up power supply maintainership from Anton Vorontov. Could
you please pull battery-2.6 git tree changes prepared for the v3.14
release.
Highlights:
- Power supply notifier
- Several drivers gained DT support
- Added Maxim 14577 driver
- Change of maintainer"
* tag 'for-v3.14' of git://git.infradead.org/battery-2.6:
MAINTAINERS: Pick up power supply maintainership
max17042_battery: Add IRQF_ONESHOT flag to use default irq handler
gpio-charger: Support wakeup events
power_supply: Add charger support for Maxim 14577
dt: Binding documentation for isp1704 charger
isp1704_charger: Add DT support
charger-manager: of_cm_parse_desc() should be static
bq2415x_charger: Add DT support
power_supply: Add power_supply_get_by_phandle
bq2415x_charger: Use power_supply notifier for automode
power: reset: Add as3722 power-off driver
mfd: AS3722: Add dt node properties for system power controller
charger-manager: Support deivce tree in charger manager driver
charger-manager: Modify the way of checking battery's temperature
power_supply: Add power_supply notifier
Pull MFD changes from Lee Jones:
"New drivers
- Samsung Maxim 14577; Micro USB, Regulator, IRQ Controller and
Battery Charger
- TI/National Semiconductor LP3943 I2C GPIO Expander and PWM
Generator
Existing driver adaptions
- Expansion of Wolfson Arizona DSP and High-Pass filter controls
- TI TWL6040 default Regmap support and Regcache addition/bypass
- Some nice Smatch catch fixes
- Conversion of TI OMAP-USB and TI TWL6030 to endian neutralness
- ChromeOS EC timing (delay) adaptions and added dependency on OF
- Many constifications of 'struct {mfd_cell,regmap_irq,et.al}'
- Watchdog support added for NVIDIA AS3722
- Convert functions to static in TI AM335x
- Realigned previously defeated functionality in TI AM335x
- IIO ADC-TSC concurrency dead-lock/timeout resolution
- Addition of Power Management and Clock support for Samsung core
- DEFINE_PCI_DEVICE_TABLE macro removal from MFD Subsystem
- Greater use of irqdomain functionality in ST-E AB8500
- Removal of 'include/linux/mfd/abx500/ab8500-gpio.h'
- Wolfson WM831x PMIC Power Management changes s/poweroff/shutdown/
- Device Tree documentation added for TI/Nat Semi LP3943
- Version detection and voltage tables for TI TPS6586x PMIC devices
- Simplification of Freescale MC13XXX (de-)initialisation routines
- Clean-up and simplification of the Realtek parent driver
- Added support for RTL8402 Realtek PCI-Express card reader
- Resource leak fix for Maxim 77686
- Possible suspend BUG() fix in OMAP USB TLL
- Support for new Wolfson WM5110 Revision (D)
- Testing of automatic assignment of of_node in mfd_add_device()
- Reversion of the above when it started to cause issues
- Remove legacy Platform Data from;
TI TWL Core, Qualcomm SSBI and ST-E ABx500 Pinctrl
- Clean-ups; tabbing issues, function name changes, 'drvdata = NULL'
removal, unused uninitialised warning mitigation, error
message clarity, removal of redundant/duplicate checks,
licensing (GPL -> GPL2), coding consistency, duplicate
function declaration, ret checks, commit corrections,
redundant of_match_ptr() helper removal, spelling,
#if-deffery removal and header guards name changes"
* tag 'mfd-3.14-1' of git://git.linaro.org/people/ljones/mfd: (78 commits)
mfd: wm5110: Add register patch for rev D chip
mfd: omap-usb-tll: Don't hold lock during pm_runtime_get/put_sync()
gpio: lp3943: Remove redundant of_match_ptr helper
mfd: sta2x11-mfd: Use named constants for pci_power_t values
Documentation: mfd: Fix LDO index in s2mps11.txt
mfd: Cleanup mfd-mcp-sa11x0.h header
mfd: max8997: Use "IS_ENABLED(CONFIG_OF)" for DT code.
mfd: twl6030: Fix endianness problem in IRQ handler
mfd: sec-core: Add cells for S5M8767-clocks
mfd: max14577: Remove redundant of_match_ptr helper
mfd: twl6040: Fix sparse non static symbol warning
mfd: Revert "mfd: Always assign of_node in mfd_add_device()"
mfd: rtsx: Fix sparse non static symbol warning
mfd: max77693: Set proper maximum register for MUIC regmap
mfd: max77686: Fix regmap resource leak on driver remove
mfd: Represent correct filenames in file headers
mfd: rtsx: Add support for card reader rtl8402
mfd: rtsx: Add set pull control macro and simplify rtl8411
mfd: max8997: Enforce mfd_add_devices() return value check
mfd: mc13xxx: Simplify probe() & remove()
...
Pull sound updates from Takashi Iwai:
"It was holiday season, so no wonder that there are little changes in
framework level, although diffstat shows quite many changes spreaded
over sound/* directories. Most of changes are cleanups, code
refactoring and fixes.
Some highlights:
- Removal of OSS sleep_on usages by Arnd
- Simplified memalloc helper codes, drop obsoleted features; now it's
built into PCM driver instead of an individual module
- Warn if PCM buffer preallocation fails, which will show page
allocation issues more clearly
- Compress offload API updates for sample rates by Vinod
- PCM glitch workaround on ctxfi emu20k1 by Sarah
- Drop cs46xx DSP blobs, using firmware loader now
- USB-audio quitks for Plantronics Gamecom 780, Creative VF0420, and
Focusrite Saffire 6
HD-audio specifics:
- Standardize Kconfigs of HD-audio codec drivers; now "make
localmodconfig" recognizes configs properly (finally!)
- Parallel PM implementation by Mengdong
- BayleyBay/ValleyView2 board fixups
- Broadwell audio support
- Runtime PM improvement (PantherPoint, etc)
- Quirks: Dell subwooer, Gigabyte mobo jack detection oddity, Dell
AiO click noise fixes, Dell headset mic fixes, etc
- Automatic bind with HDMI codec parser without generic parser
- More AD codec fixes (since 3.12 regression) including the automatic
stereo mix support
- Common Thinkpad ACPI helper for Realtek and Conexant codecs
ASoC specifics:
- Update to the generic DMA code to support deferred probe and
managed resources
- New drivers for BCM2835 (used in Raspberry Pi), Tegra with MAX98090
and Analog Devices AXI I2S and S/PDIF controller IPs
- Device tree support for the simple card, max98090 and cs42l52
- Conversion of the Samsung drivers to native dmaengine, making them
multiplatform compatible and hopefully helping keep them more
modern and up to date.
- More regmap conversions, including a very welcome one for twl6040
from Peter Ujfalusi
- A big overhaul of the DaVinci drivers also from Peter Ujfalusi
- Lots of DMA updates from Lars-Peter
- Improvements to the constraints handling code from Lars-Peter
- A very helpful conversion of the TWL4030 driver to regmap from Peter
- A new driver for the Freescale ESAI controller from Nicolin Chen
- Conversion of some of the drivers to use params_width()
- Extensions to DPCM for use with compressed audio from Liam"
* tag 'sound-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (396 commits)
ASoC: dapm: Fix double prefix addition
ASoC: compress: Add suport for DPCM into compressed audio
ASoC: DPCM: make some DPCM API calls non static for compressed usage
ASoC: core: Fix possible NULL pointer dereference of pcm->config
ALSA: hda - add headset mic detect quirks for some Dell machines
ASoC: tlv320aic32x4: Fix regmap range_min
ASoC: core: Return -ENOTSUPP from set_sysclk() if no operation provided
ASoC: dapm: Change prototype of soc_widget_read
ASoC: samsung: Remove SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag
ASoC: axi-{spdif,i2s}: Remove SND_DMAENGINE_PCM_FLAG_NO_RESIDUE flag
ASoC: generic-dmaengine-pcm: Check DMA residue granularity
ASoC: generic-dmaengine-pcm: Check NO_RESIDUE flag at runtime
dma: pl330: Set residue_granularity
dma: Indicate residue granularity in dma_slave_caps
ASoC: simple-card: fix one bug to writing to the platform data
ASoC: pcm: Use snd_pcm_rate_mask_intersect() helper
ALSA: Add helper function for intersecting two rate masks
ASoC: s6000: Don't mix SNDRV_PCM_RATE_CONTINUOUS with specific rates
ASoC: fsl: Don't mix SNDRV_PCM_RATE_CONTINUOUS with specific rates
ASoC: pcm: Properly initialize hw->rate_max
...
Pull bulk pin control changes from Linus Walleij:
"This has been queued and tested for a while. Lots of action here,
like in the GPIO tree, embedded stuff like this is really hot now it
seems. Details in the signed tag. I'm especially happy about the
Qualcomm driver as it is used in such a huge subset of mobile handsets
out there, and these platforms in general need better upstream support
- New driver for the Qualcomm TLMM pin controller and its msm8x74
subdriver.
- New driver for the Broadcom Capri BCM281xx SoC.
- New subdriver for the imx25 pin controller.
- New subdriver for the Tegra124 pin controller.
- Lock GPIO lines as IRQs for select combined pin control and GPIO
drivers for baytrail and sirf.
- Some semi-big refactorings and extenstions to the sirf driver.
- Lots of patching, cleanup and fixing in the Renesas "PFC" driver
and associated subdrivers as usual. It is settling down a little
bit now it seems.
- Minor fixes and incremental updates here and there as usual"
* tag 'pinctrl-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (72 commits)
pinctrl: sunxi: Honor GPIO output initial vaules
pinctrl: capri: add dependency on OF
ARM: bcm11351: Enable pinctrl for Broadcom Capri SoCs
ARM: pinctrl: Add Broadcom Capri pinctrl driver
pinctrl: Add pinctrl binding for Broadcom Capri SoCs
pinctrl: Add void * to pinctrl_pin_desc
pinctrl: st: Fix a typo in probe
pinctrl: Fix some typos and grammar issues in the documentation
pinctrl: sirf: lock IRQs when starting them
pinctrl: sirf: put gpio interrupt pin into input status automatically
pinctrl: sirf: use only one irq_domain for the whole device node
pinctrl: single: fix infinite loop caused by bad mask
pinctrl: single: fix pcs_disable with bits_per_mux
pinctrl: single: fix DT bindings documentation
pinctrl: as3722: Set pin to output mode for some function
pinctrl: sirf: add pin group for USP0 with only RX or TX frame sync
pinctrl: sirf: fix the pins of sdmmc5 connected with TriG
pinctrl: sirf: add lost usp1_uart_nostreamctrl group for atlas6
pinctrl: sunxi: Add Allwinner A20 clock output pin functions
pinctrl/lantiq: fix typo
...
Pull GPIO tree bulk changes from Linus Walleij:
"A big set this merge window, as we have much going on in this
subsystem. The changes to other subsystems (notably a slew of ARM
machines as I am doing away with their custom APIs) have all been
ACKed to the extent possible.
Major changes this time:
- Some core improvements and cleanups to the new GPIO descriptor API.
This seems to be working now so we can start the exodus to this
API, moving gradually away from the global GPIO numberspace.
- Incremental improvements to the ACPI GPIO core, and move the few
GPIO ACPI clients we have to the GPIO descriptor API right *now*
before we go any further. We actually managed to contain this
*before* we started to litter the kernel with yet another hackish
global numberspace for the ACPI GPIOs, which is a big win.
- The RFkill GPIO driver and all platforms using it have been
migrated to use the GPIO descriptors rather than fixed number
assignments. Tegra machine has been migrated as part of this.
- New drivers for MOXA ART, Xtensa GPIO32 and SMSC SCH311x. Those
should be really good examples of how I expect a nice GPIO driver
to look these days.
- Do away with custom GPIO implementations on a major part of the ARM
machines: ks8695, lpc32xx, mv78xx0. Make a first step towards the
same in the horribly convoluted Samsung S3C include forest. We
expect to continue to clean this up as we move forward.
- Flag GPIO lines used for IRQ on adnp, bcm-kona, em, intel-mid and
lynxpoint.
This makes the GPIOlib core aware that a certain GPIO line is used
for IRQs and can then enforce some semantics such as disallowing a
GPIO line marked as in use for IRQ to be switched to output mode.
- Drop all use of irq_set_chip_and_handler_name(). The name provided
in these cases were just unhelpful tags like "mux" or "demux".
- Extend the MCP23s08 driver to handle interrupts.
- Minor incremental improvements for rcar, lynxpoint, em 74x164 and
msm drivers.
- Some non-urgent bug fixes here and there, duplicate #includes and
that usual kind of cleanups"
Fix up broken Kconfig file manually to make this all compile.
* tag 'gpio-v3.14-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
gpio: mcp23s08: fix casting caused build warning
gpio: mcp23s08: depend on OF_GPIO
gpio: mcp23s08: Add irq functionality for i2c chips
ARM: S5P[v210|c100|64x0]: Fix build error
gpio: pxa: clamp gpio get value to [0,1]
ARM: s3c24xx: explicit dependency on <plat/gpio-cfg.h>
ARM: S3C[24|64]xx: move includes back under <mach/> scope
Documentation / ACPI: update to GPIO descriptor API
gpio / ACPI: get rid of acpi_gpio.h
gpio / ACPI: register to ACPI events automatically
mmc: sdhci-acpi: convert to use GPIO descriptor API
ARM: s3c24xx: fix build error
gpio: f7188x: set can_sleep attribute
gpio: samsung: Update documentation
gpio: samsung: Remove hardware.h inclusion
gpio: xtensa: depend on HAVE_XTENSA_GPIO32
gpio: clps711x: Enable driver compilation with COMPILE_TEST
gpio: clps711x: Use of_match_ptr()
net: rfkill: gpio: convert to descriptor-based GPIO interface
leds: s3c24xx: Fix build failure
...
Pull i2c updates from Wolfram Sang:
"For 3.14, the I2C subsystem has the following to offer:
- new drivers for Renesas RIIC and RobotFuzz OSIF
- driver cleanups & improvements & bugfixes
Pretty standard stuff this time, I'd say. There is more complex stuff
coming up, but I didn't have the bandwidth between the years to pull
it in for this release. Sadly"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (26 commits)
i2c: s3c2410: fix quirk usage for 64-bit
i2c: pnx: Use devm_*() functions
i2c: at91: add a new compatibility string for the at91sam9261
i2c-ismt: support I2C_SMBUS_I2C_BLOCK_DATA transaction type
i2c: Add bus driver for for OSIF USB i2c device.
i2c: i2c-tiny-usb: Remove RobotFuzz USB vendor:product ID
i2c: designware: remove HAVE_CLK build dependecy
Documentation: i2c: Remove obsolete example
i2c: nomadik: remove platform data header
i2c: nomadik: auto-calculate slave setup time
i2c: viperboard: remove superfluous assignment
i2c: xilinx: Use devm_* functions
i2c: xilinx: Do not enable irq before irq handler
i2c: xilinx: Fix i2c checkpatch warnings
i2c: at91: document clock properties
i2c: isch: Use devm_request_region()
i2c: viperboard: Use devm_kzalloc() functions
i2c: imx: propagate irq error code in probe
i2c: s3c2410: dont need CPU_FREQ transitions for exynos series
i2c: s3c2410: Add polling mode support
...
Pull security layer updates from James Morris:
"Changes for this kernel include maintenance updates for Smack, SELinux
(and several networking fixes), IMA and TPM"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (39 commits)
SELinux: Fix memory leak upon loading policy
tpm/tpm-sysfs: active_show() can be static
tpm: tpm_tis: Fix compile problems with CONFIG_PM_SLEEP/CONFIG_PNP
tpm: Make tpm-dev allocate a per-file structure
tpm: Use the ops structure instead of a copy in tpm_vendor_specific
tpm: Create a tpm_class_ops structure and use it in the drivers
tpm: Pull all driver sysfs code into tpm-sysfs.c
tpm: Move sysfs functions from tpm-interface to tpm-sysfs
tpm: Pull everything related to /dev/tpmX into tpm-dev.c
char: tpm: nuvoton: remove unused variable
tpm: MAINTAINERS: Cleanup TPM Maintainers file
tpm/tpm_i2c_atmel: fix coccinelle warnings
tpm/tpm_ibmvtpm: fix unreachable code warning (smatch warning)
tpm/tpm_i2c_stm_st33: Check return code of get_burstcount
tpm/tpm_ppi: Check return value of acpi_get_name
tpm/tpm_ppi: Do not compare strcmp(a,b) == -1
ima: remove unneeded size_limit argument from ima_eventdigest_init_common()
ima: update IMA-templates.txt documentation
ima: pass HASH_ALGO__LAST as hash algo in ima_eventdigest_init()
ima: change the default hash algorithm to SHA1 in ima_eventdigest_ng_init()
...
Commit a1fd844c6e ("ARM: sa1100: move platform_data definitions")
moved the file to the current location but forgot to remove the pointer
to its previous location. Clean it up. While at it also change the header
file protection macros appropriately.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The original author(s) probably copy/pasted these headers from the
existing public header files.
Signed-off-by: Laszlo Papp <lpapp@kde.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
mc13xxx_get_flags() declaration given twice.
This patch removes this duplicate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In preparation for passing a const pointer directly to
ssbi_write() from the regmap APIs.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ssbi driver assumes that the device is DT based. Remove the
platform data structs that will never be used and hide the enum
in the only C file that uses it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the VERSIONCRC to determine the exact device version. According to
the datasheet this register can be used as device identifier. The
identification is needed since some tps6586x regulators use a different
voltage table.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
