Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
Pull networking updates from Jakub Kicinski:
"The sprinkling of SPI drivers is because we added a new one and Mark
sent us a SPI driver interface conversion pull request.
Core
----
- Introduce XDP multi-buffer support, allowing the use of XDP with
jumbo frame MTUs and combination with Rx coalescing offloads (LRO).
- Speed up netns dismantling (5x) and lower the memory cost a little.
Remove unnecessary per-netns sockets. Scope some lists to a netns.
Cut down RCU syncing. Use batch methods. Allow netdev registration
to complete out of order.
- Support distinguishing timestamp types (ingress vs egress) and
maintaining them across packet scrubbing points (e.g. redirect).
- Continue the work of annotating packet drop reasons throughout the
stack.
- Switch netdev error counters from an atomic to dynamically
allocated per-CPU counters.
- Rework a few preempt_disable(), local_irq_save() and busy waiting
sections problematic on PREEMPT_RT.
- Extend the ref_tracker to allow catching use-after-free bugs.
BPF
---
- Introduce "packing allocator" for BPF JIT images. JITed code is
marked read only, and used to be allocated at page granularity.
Custom allocator allows for more efficient memory use, lower iTLB
pressure and prevents identity mapping huge pages from getting
split.
- Make use of BTF type annotations (e.g. __user, __percpu) to enforce
the correct probe read access method, add appropriate helpers.
- Convert the BPF preload to use light skeleton and drop the
user-mode-driver dependency.
- Allow XDP BPF_PROG_RUN test infra to send real packets, enabling
its use as a packet generator.
- Allow local storage memory to be allocated with GFP_KERNEL if
called from a hook allowed to sleep.
- Introduce fprobe (multi kprobe) to speed up mass attachment (arch
bits to come later).
- Add unstable conntrack lookup helpers for BPF by using the BPF
kfunc infra.
- Allow cgroup BPF progs to return custom errors to user space.
- Add support for AF_UNIX iterator batching.
- Allow iterator programs to use sleepable helpers.
- Support JIT of add, and, or, xor and xchg atomic ops on arm64.
- Add BTFGen support to bpftool which allows to use CO-RE in kernels
without BTF info.
- Large number of libbpf API improvements, cleanups and deprecations.
Protocols
---------
- Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev.
- Adjust TSO packet sizes based on min_rtt, allowing very low latency
links (data centers) to always send full-sized TSO super-frames.
- Make IPv6 flow label changes (AKA hash rethink) more configurable,
via sysctl and setsockopt. Distinguish between server and client
behavior.
- VxLAN support to "collect metadata" devices to terminate only
configured VNIs. This is similar to VLAN filtering in the bridge.
- Support inserting IPv6 IOAM information to a fraction of frames.
- Add protocol attribute to IP addresses to allow identifying where
given address comes from (kernel-generated, DHCP etc.)
- Support setting socket and IPv6 options via cmsg on ping6 sockets.
- Reject mis-use of ECN bits in IP headers as part of DSCP/TOS.
Define dscp_t and stop taking ECN bits into account in fib-rules.
- Add support for locked bridge ports (for 802.1X).
- tun: support NAPI for packets received from batched XDP buffs,
doubling the performance in some scenarios.
- IPv6 extension header handling in Open vSwitch.
- Support IPv6 control message load balancing in bonding, prevent
neighbor solicitation and advertisement from using the wrong port.
Support NS/NA monitor selection similar to existing ARP monitor.
- SMC
- improve performance with TCP_CORK and sendfile()
- support auto-corking
- support TCP_NODELAY
- MCTP (Management Component Transport Protocol)
- add user space tag control interface
- I2C binding driver (as specified by DMTF DSP0237)
- Multi-BSSID beacon handling in AP mode for WiFi.
- Bluetooth:
- handle MSFT Monitor Device Event
- add MGMT Adv Monitor Device Found/Lost events
- Multi-Path TCP:
- add support for the SO_SNDTIMEO socket option
- lots of selftest cleanups and improvements
- Increase the max PDU size in CAN ISOTP to 64 kB.
Driver API
----------
- Add HW counters for SW netdevs, a mechanism for devices which
offload packet forwarding to report packet statistics back to
software interfaces such as tunnels.
- Select the default NIC queue count as a fraction of number of
physical CPU cores, instead of hard-coding to 8.
- Expose devlink instance locks to drivers. Allow device layer of
drivers to use that lock directly instead of creating their own
which always runs into ordering issues in devlink callbacks.
- Add header/data split indication to guide user space enabling of
TCP zero-copy Rx.
- Allow configuring completion queue event size.
- Refactor page_pool to enable fragmenting after allocation.
- Add allocation and page reuse statistics to page_pool.
- Improve Multiple Spanning Trees support in the bridge to allow
reuse of topologies across VLANs, saving HW resources in switches.
- DSA (Distributed Switch Architecture):
- replay and offload of host VLAN entries
- offload of static and local FDB entries on LAG interfaces
- FDB isolation and unicast filtering
New hardware / drivers
----------------------
- Ethernet:
- LAN937x T1 PHYs
- Davicom DM9051 SPI NIC driver
- Realtek RTL8367S, RTL8367RB-VB switch and MDIO
- Microchip ksz8563 switches
- Netronome NFP3800 SmartNICs
- Fungible SmartNICs
- MediaTek MT8195 switches
- WiFi:
- mt76: MediaTek mt7916
- mt76: MediaTek mt7921u USB adapters
- brcmfmac: Broadcom BCM43454/6
- Mobile:
- iosm: Intel M.2 7360 WWAN card
Drivers
-------
- Convert many drivers to the new phylink API built for split PCS
designs but also simplifying other cases.
- Intel Ethernet NICs:
- add TTY for GNSS module for E810T device
- improve AF_XDP performance
- GTP-C and GTP-U filter offload
- QinQ VLAN support
- Mellanox Ethernet NICs (mlx5):
- support xdp->data_meta
- multi-buffer XDP
- offload tc push_eth and pop_eth actions
- Netronome Ethernet NICs (nfp):
- flow-independent tc action hardware offload (police / meter)
- AF_XDP
- Other Ethernet NICs:
- at803x: fiber and SFP support
- xgmac: mdio: preamble suppression and custom MDC frequencies
- r8169: enable ASPM L1.2 if system vendor flags it as safe
- macb/gem: ZynqMP SGMII
- hns3: add TX push mode
- dpaa2-eth: software TSO
- lan743x: multi-queue, mdio, SGMII, PTP
- axienet: NAPI and GRO support
- Mellanox Ethernet switches (mlxsw):
- source and dest IP address rewrites
- RJ45 ports
- Marvell Ethernet switches (prestera):
- basic routing offload
- multi-chain TC ACL offload
- NXP embedded Ethernet switches (ocelot & felix):
- PTP over UDP with the ocelot-8021q DSA tagging protocol
- basic QoS classification on Felix DSA switch using dcbnl
- port mirroring for ocelot switches
- Microchip high-speed industrial Ethernet (sparx5):
- offloading of bridge port flooding flags
- PTP Hardware Clock
- Other embedded switches:
- lan966x: PTP Hardward Clock
- qca8k: mdio read/write operations via crafted Ethernet packets
- Qualcomm 802.11ax WiFi (ath11k):
- add LDPC FEC type and 802.11ax High Efficiency data in radiotap
- enable RX PPDU stats in monitor co-exist mode
- Intel WiFi (iwlwifi):
- UHB TAS enablement via BIOS
- band disablement via BIOS
- channel switch offload
- 32 Rx AMPDU sessions in newer devices
- MediaTek WiFi (mt76):
- background radar detection
- thermal management improvements on mt7915
- SAR support for more mt76 platforms
- MBSSID and 6 GHz band on mt7915
- RealTek WiFi:
- rtw89: AP mode
- rtw89: 160 MHz channels and 6 GHz band
- rtw89: hardware scan
- Bluetooth:
- mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS)
- Microchip CAN (mcp251xfd):
- multiple RX-FIFOs and runtime configurable RX/TX rings
- internal PLL, runtime PM handling simplification
- improve chip detection and error handling after wakeup"
* tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits)
llc: fix netdevice reference leaks in llc_ui_bind()
drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool
ice: don't allow to run ice_send_event_to_aux() in atomic ctx
ice: fix 'scheduling while atomic' on aux critical err interrupt
net/sched: fix incorrect vlan_push_eth dest field
net: bridge: mst: Restrict info size queries to bridge ports
net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init()
drivers: net: xgene: Fix regression in CRC stripping
net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT
net: dsa: fix missing host-filtered multicast addresses
net/mlx5e: Fix build warning, detected write beyond size of field
iwlwifi: mvm: Don't fail if PPAG isn't supported
selftests/bpf: Fix kprobe_multi test.
Revert "rethook: x86: Add rethook x86 implementation"
Revert "arm64: rethook: Add arm64 rethook implementation"
Revert "powerpc: Add rethook support"
Revert "ARM: rethook: Add rethook arm implementation"
netdevice: add missing dm_private kdoc
net: bridge: mst: prevent NULL deref in br_mst_info_size()
selftests: forwarding: Use same VRF for port and VLAN upper
...
Enable binding the nfp driver to NFP3800 and NFP3803 devices.
The PCIE_SRAM offset is different for the NFP3800 device, which also
only supports a single explicit group.
Changes to Dirk's work:
* 48-bit dma addressing is not ready yet. Keep 40-bit dma addressing
for NFP3800.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver updates for 5.17-rc1.
Nothing major in here, just lots of good updates and fixes, including:
- more tty core cleanups from Jiri as well as mxser driver cleanups.
This is the majority of the core diffstat
- tty documentation updates from Jiri
- platform_get_irq() updates
- various serial driver updates for new features and hardware
- fifo usage for 8250 console, reducing cpu load a lot
- LED fix for keyboards, long-time bugfix that went through many
revisions
- minor cleanups
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: core: Keep mctrl register state and cached copy in sync
serial: stm32: correct loop for dma error handling
serial: stm32: fix flow control transfer in DMA mode
serial: stm32: rework TX DMA state condition
serial: stm32: move tx dma terminate DMA to shutdown
serial: pl011: Drop redundant DTR/RTS preservation on close/open
serial: pl011: Drop CR register reset on set_termios
serial: pl010: Drop CR register reset on set_termios
serial: liteuart: fix MODULE_ALIAS
serial: 8250_bcm7271: Fix return error code in case of dma_alloc_coherent() failure
Revert "serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2"
tty: goldfish: Use platform_get_irq() to get the interrupt
serdev: BREAK/FRAME/PARITY/OVERRUN notification prototype V2
tty: serial: meson: Drop the legacy compatible strings and clock code
serial: pmac_zilog: Use platform_get_irq() to get the interrupt
serial: bcm63xx: Use platform_get_irq() to get the interrupt
serial: ar933x: Use platform_get_irq() to get the interrupt
serial: vt8500: Use platform_get_irq() to get the interrupt
serial: altera_jtaguart: Use platform_get_irq_optional() to get the interrupt
serial: pxa: Use platform_get_irq() to get the interrupt
...
Pull hwmon updates from Guenter Roeck:
"New drivers for:
- Aquacomputer D5 Next
- SB-RMI power module
Added chip support to existing drivers:
- Support for various Zen2 and Zen3 APUs and for Yellow Carp (SMU
v13) added to k10temp driver
- Support for Silicom n5010 PAC added to intel-m10-bmc driver
- Support for BPD-RS600 added to pmbus/bpa-rs600 driver
Other notable changes:
- In k10temp, do not display Tdie on Zen CPUs if there is no
difference between Tdie and Tctl
- Converted adt7470 and dell-smm drivers to use
devm_hwmon_device_register_with_info API
- Support for temperature/pwm tables added to axi-fan-control driver
- Enabled fan control for Dell Precision 7510 in dell-smm driver
Various other minor improvements and fixes in several drivers"
* tag 'hwmon-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (41 commits)
hwmon: add driver for Aquacomputer D5 Next
hwmon: (adt7470) Convert to devm_hwmon_device_register_with_info API
hwmon: (adt7470) Convert to use regmap
hwmon: (adt7470) Fix some style issues
hwmon: (k10temp) Add support for yellow carp
hwmon: (k10temp) Rework the temperature offset calculation
hwmon: (k10temp) Don't show Tdie for all Zen/Zen2/Zen3 CPU/APU
hwmon: (k10temp) Add additional missing Zen2 and Zen3 APUs
hwmon: remove amd_energy driver in Makefile
hwmon: (dell-smm) Rework SMM function debugging
hwmon: (dell-smm) Mark i8k_get_fan_nominal_speed as __init
hwmon: (dell-smm) Mark tables as __initconst
hwmon: (pmbus/bpa-rs600) Add workaround for incorrect Pin max
hwmon: (pmbus/bpa-rs600) Don't use rated limits as warn limits
hwmon: (axi-fan-control) Support temperature vs pwm points
hwmon: (axi-fan-control) Handle irqs in natural order
hwmon: (axi-fan-control) Make sure the clock is enabled
hwmon: (pmbus/ibm-cffps) Fix write bits for LED control
hwmon: (w83781d) Match on device tree compatibles
dt-bindings: hwmon: Add bindings for Winbond W83781D
...
The Intel 82426EX ISA Bridge (IB), a part of the Intel 82420EX PCIset,
implements PCI interrupt steering with a PIRQ router in the form of two
PIRQ Route Control registers, available in the PCI configuration space
at locations 0x66 and 0x67 for the PIRQ0# and PIRQ1# lines respectively.
The semantics is the same as with the PIIX router, however it is not
clear if BIOSes use register indices or line numbers as the cookie to
identify PCI interrupts in their routing tables and therefore support
either scheme.
The IB is directly attached to the Intel 82425EX PCI System Controller
(PSC) component of the chipset via a dedicated PSC/IB Link interface
rather than the host bus or PCI. Therefore it does not itself appear in
the PCI configuration space even though it responds to configuration
cycles addressing registers it implements. Use 82425EX's identification
then for determining the presence of the IB.
References:
[1] "82420EX PCIset Data Sheet, 82425EX PCI System Controller (PSC) and
82426EX ISA Bridge (IB)", Intel Corporation, Order Number:
290488-004, December 1995, Section 3.3.18 "PIRQ1RC/PIRQ0RC--PIRQ
Route Control Registers", p. 61
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107200213490.9461@angie.orcam.me.uk
The ALi M1487 ISA Bus Controller (IBC), a part of the ALi FinALi 486
chipset, implements PCI interrupt steering with a PIRQ router[1] in the
form of four 4-bit mappings, spread across two PCI INTx Routing Table
Mapping Registers, available in the port I/O space accessible indirectly
via the index/data register pair at 0x22/0x23, located at indices 0x42
and 0x43 for the INT1/INT2 and INT3/INT4 lines respectively.
Additionally there is a separate PCI INTx Sensitivity Register at index
0x44 in the same port I/O space, whose bits 3:0 select the trigger mode
for INT[4:1] lines respectively[2]. Manufacturer's documentation says
that this register has to be set consistently with the relevant ELCR
register[3]. Add a router-specific hook then and use it to handle this
register.
Accesses to the port I/O space concerned here need to be unlocked by
writing the value of 0xc5 to the Lock Register at index 0x03
beforehand[4]. Do so then and then lock access after use for safety.
The IBC is implemented as a peer bridge on the host bus rather than a
southbridge on PCI and therefore it does not itself appear in the PCI
configuration space. It is complemented by the M1489 Cache-Memory PCI
Controller (CMP) host-to-PCI bridge, so use that device's identification
for determining the presence of the IBC.
References:
[1] "M1489/M1487: 486 PCI Chip Set", Version 1.2, Acer Laboratories
Inc., July 1997, Section 4: "Configuration Registers", pp. 76-77
[2] same, p. 77
[3] same, Section 5: "M1489/M1487 Software Programming Guide", pp.
99-100
[4] same, Section 4: "Configuration Registers", p. 37
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2107191702020.9461@angie.orcam.me.uk
Pull x86 cpu updates from Borislav Petkov:
- New AMD models support
- Allow MONITOR/MWAIT to be used for C1 state entry on Hygon too
- Use the special RAPL CPUID bit to detect the functionality on AMD and
Hygon instead of doing family matching.
- Add support for new Intel microcode deprecating TSX on some models
and do not enable kernel workarounds for those CPUs when TSX
transactions always abort, as a result of that microcode update.
* tag 'x86_cpu_for_v5.14_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tsx: Clear CPUID bits when TSX always force aborts
x86/events/intel: Do not deploy TSX force abort workaround when TSX is deprecated
x86/msr: Define new bits in TSX_FORCE_ABORT MSR
perf/x86/rapl: Use CPUID bit on AMD and Hygon parts
x86/cstate: Allow ACPI C1 FFH MWAIT use on Hygon systems
x86/amd_nb: Add AMD family 19h model 50h PCI ids
x86/cpu: Fix core name for Sapphire Rapids
While the driver is still marked as maintained in MAINTAINERS, Comtrol
does not really care about this ancient driver. They are still
manufacturing serial devices, but those are controlled only by
out-of-tree drivers.
Comtrol didn't answer my pings, so this driver is apparently
unmaintained. Aside from that, the driver was untouched for years, only
whole-tree changes happened during the past years. The driver needs much
more care, so drop it for now. If someone steps up to reintroduce it,
they need to clean it up first.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cyclades driver was orphaned by commit d459883e6c (MAINTAINERS:
remove two dead e-mail) 13 years ago. Noone stepped up to take care of
them and to fix all the issues the driver has.
On the top of that, there is no way to obtain the firmware for Z cards
from the vendor as cyclades.com ceased to exist.
So it's time to drop the driver with all its traces.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210302062214.29627-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Remove unnecessary locking around _OSC (Bjorn Helgaas)
- Clarify message about _OSC failure (Bjorn Helgaas)
- Remove notification of PCIe bandwidth changes (Bjorn Helgaas)
- Tidy checking of syscall user config accessors (Heiner Kallweit)
Resource management:
- Decline to resize resources if boot config must be preserved (Ard
Biesheuvel)
- Fix pci_register_io_range() memory leak (Geert Uytterhoeven)
Error handling (Keith Busch):
- Clear error status from the correct device
- Retain error recovery status so drivers can use it after reset
- Log the type of Port (Root or Switch Downstream) that we reset
- Always request a reset for Downstream Ports in frozen state
Endpoint framework and NTB (Kishon Vijay Abraham I):
- Make *_get_first_free_bar() take into account 64 bit BAR
- Add helper API to get the 'next' unreserved BAR
- Make *_free_bar() return error codes on failure
- Remove unused pci_epf_match_device()
- Add support to associate secondary EPC with EPF
- Add support in configfs to associate two EPCs with EPF
- Add pci_epc_ops to map MSI IRQ
- Add pci_epf_ops to expose function-specific attrs
- Allow user to create sub-directory of 'EPF Device' directory
- Implement ->msi_map_irq() ops for cadence
- Configure LM_EP_FUNC_CFG based on epc->function_num_map for cadence
- Add EP function driver to provide NTB functionality
- Add support for EPF PCI Non-Transparent Bridge
- Add specification for PCI NTB function device
- Add PCI endpoint NTB function user guide
- Add configfs binding documentation for pci-ntb endpoint function
Broadcom STB PCIe controller driver:
- Add support for BCM4908 and external PERST# signal controller
(Rafał Miłecki)
Cadence PCIe controller driver:
- Retrain Link to work around Gen2 training defect (Nadeem Athani)
- Fix merge botch in cdns_pcie_host_map_dma_ranges() (Krzysztof
Wilczyński)
Freescale Layerscape PCIe controller driver:
- Add LX2160A rev2 EP mode support (Hou Zhiqiang)
- Convert to builtin_platform_driver() (Michael Walle)
MediaTek PCIe controller driver:
- Fix OF node reference leak (Krzysztof Wilczyński)
Microchip PolarFlare PCIe controller driver:
- Add Microchip PolarFire PCIe controller driver (Daire McNamara)
Qualcomm PCIe controller driver:
- Use PHY_REFCLK_USE_PAD only for ipq8064 (Ansuel Smith)
- Add support for ddrss_sf_tbu clock for sm8250 (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Drop PCIE_RCAR config option (Lad Prabhakar)
- Always allocate MSI addresses in 32bit space (Marek Vasut)
Rockchip PCIe controller driver:
- Add FriendlyARM NanoPi M4B DT binding (Chen-Yu Tsai)
- Make 'ep-gpios' DT property optional (Chen-Yu Tsai)
Synopsys DesignWare PCIe controller driver:
- Work around ECRC configuration hardware defect (Vidya Sagar)
- Drop support for config space in DT 'ranges' (Rob Herring)
- Change size to u64 for EP outbound iATU (Shradha Todi)
- Add upper limit address for outbound iATU (Shradha Todi)
- Make dw_pcie ops optional (Jisheng Zhang)
- Remove unnecessary dw_pcie_ops from al driver (Jisheng Zhang)
Xilinx Versal CPM PCIe controller driver:
- Fix OF node reference leak (Pan Bian)
Miscellaneous:
- Remove tango host controller driver (Arnd Bergmann)
- Remove IRQ handler & data together (altera-msi, brcmstb, dwc)
(Martin Kaiser)
- Fix xgene-msi race in installing chained IRQ handler (Martin
Kaiser)
- Apply CONFIG_PCI_DEBUG to entire drivers/pci hierarchy (Junhao He)
- Fix pci-bridge-emul array overruns (Russell King)
- Remove obsolete uses of WARN_ON(in_interrupt()) (Sebastian Andrzej
Siewior)"
* tag 'pci-v5.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (69 commits)
PCI: qcom: Use PHY_REFCLK_USE_PAD only for ipq8064
PCI: qcom: Add support for ddrss_sf_tbu clock
dt-bindings: PCI: qcom: Document ddrss_sf_tbu clock for sm8250
PCI: al: Remove useless dw_pcie_ops
PCI: dwc: Don't assume the ops in dw_pcie always exist
PCI: dwc: Add upper limit address for outbound iATU
PCI: dwc: Change size to u64 for EP outbound iATU
PCI: dwc: Drop support for config space in 'ranges'
PCI: layerscape: Convert to builtin_platform_driver()
PCI: layerscape: Add LX2160A rev2 EP mode support
dt-bindings: PCI: layerscape: Add LX2160A rev2 compatible strings
PCI: dwc: Work around ECRC configuration issue
PCI/portdrv: Report reset for frozen channel
PCI/AER: Specify the type of Port that was reset
PCI/ERR: Retain status from error notification
PCI/AER: Clear AER status from Root Port when resetting Downstream Port
PCI/ERR: Clear status of the reporting device
dt-bindings: arm: rockchip: Add FriendlyARM NanoPi M4B
PCI: rockchip: Make 'ep-gpios' DT property optional
Documentation: PCI: Add PCI endpoint NTB function user guide
...
- Account for 64-bit BARs in pci_epc_get_first_free_bar() (Kishon Vijay
Abraham I)
- Add pci_epc_get_next_free_bar() helper (Kishon Vijay Abraham I)
- Return error codes on failure of endpoint BAR interfaces (Kishon Vijay
Abraham I)
- Remove unused pci_epf_match_device() (Kishon Vijay Abraham I)
- Add support for secondary endpoint controller to prepare for NTB endpoint
functionality (Kishon Vijay Abraham I)
- Add configfs support for secondary endpoint controller (Kishon Vijay
Abraham I)
- Add MSI address mapping ops for NTB doorbell support (Kishon Vijay
Abraham I)
- Add ops for endpoint function-specific attributes (Kishon Vijay Abraham
I)
- Allow configfs subdirectory for endpoint function configuration (Kishon
Vijay Abraham I)
- Implement cadence MSI address mapping ops (Kishon Vijay Abraham I)
- Configure cadence LM_EP_FUNC_CFG based on epc->function_num_map (Kishon
Vijay Abraham I)
- Add endpoint-side driver to provide NTB functionality (Kishon Vijay
Abraham I)
- Add host-side driver for generic EPF NTB functionality (Kishon Vijay
Abraham I)
- Document NTB endpoint functionality (Kishon Vijay Abraham I)
* pci/ntb:
Documentation: PCI: Add PCI endpoint NTB function user guide
Documentation: PCI: Add configfs binding documentation for pci-ntb endpoint function
NTB: Add support for EPF PCI Non-Transparent Bridge
PCI: Add TI J721E device to PCI IDs
PCI: endpoint: Add EP function driver to provide NTB functionality
PCI: cadence: Configure LM_EP_FUNC_CFG based on epc->function_num_map
PCI: cadence: Implement ->msi_map_irq() ops
PCI: endpoint: Allow user to create sub-directory of 'EPF Device' directory
PCI: endpoint: Add pci_epf_ops to expose function-specific attrs
PCI: endpoint: Add pci_epc_ops to map MSI IRQ
PCI: endpoint: Add support in configfs to associate two EPCs with EPF
PCI: endpoint: Add support to associate secondary EPC with EPF
PCI: endpoint: Remove unused pci_epf_match_device()
PCI: endpoint: Make *_free_bar() to return error codes on failure
PCI: endpoint: Add helper API to get the 'next' unreserved BAR
PCI: endpoint: Make *_get_first_free_bar() take into account 64 bit BAR
Documentation: PCI: Add specification for the PCI NTB function device
The CXL.mem protocol allows a device to act as a provider of "System
RAM" and/or "Persistent Memory" that is fully coherent as if the memory
was attached to the typical CPU memory controller.
With the CXL-2.0 specification a PCI endpoint can implement a "Type-3"
device interface and give the operating system control over "Host
Managed Device Memory". See section 2.3 Type 3 CXL Device.
The memory range exported by the device may optionally be described by
the platform firmware memory map, or by infrastructure like LIBNVDIMM to
provision persistent memory capacity from one, or more, CXL.mem devices.
A pre-requisite for Linux-managed memory-capacity provisioning is this
cxl_mem driver that can speak the mailbox protocol defined in section
8.2.8.4 Mailbox Registers.
For now just land the initial driver boiler-plate and Documentation/
infrastructure.
Signed-off-by: Ben Widawsky <ben.widawsky@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: David Rientjes <rientjes@google.com> (v1)
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://www.computeexpresslink.org/download-the-specification
Link: https://lore.kernel.org/r/20210217040958.1354670-2-ben.widawsky@intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If a Root Complex Integrated Endpoint (RCiEP) is implemented, it may signal
errors through a Root Complex Event Collector (RCEC). Each RCiEP must be
associated with no more than one RCEC.
For an RCEC (which is technically not a Bridge), error messages "received"
from associated RCiEPs must be enabled for "transmission" in order to cause
a System Error via the Root Control register or (when the Advanced Error
Reporting Capability is present) reporting via the Root Error Command
register and logging in the Root Error Status register and Error Source
Identification register.
Given the commonality with Root Ports and the need to also support AER and
PME services for RCECs, extend the Root Port driver to support RCEC devices
by adding the RCEC Class ID to the driver structure.
Co-developed-by: Sean V Kelley <sean.v.kelley@intel.com>
Link: https://lore.kernel.org/r/20201121001036.8560-3-sean.v.kelley@intel.com
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # non-native/no RCEC
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
Signed-off-by: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
to fixup conflicts in arch/x86/kernel/cpu/mce/core.c so MCE specific follow
up patches can be applied without creating a horrible merge conflict
afterwards.
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
- Add mediatek support for MT7629 (Jianjun Wang)
* remotes/lorenzo/pci/mediatek:
PCI: mediatek: Add controller support for MT7629
dt-bindings: PCI: Add support for MT7629
Pull sound updates from Takashi Iwai:
"As shown in diffstat and logs, it was again a busy development cycle
at this time, too. The most significant changes are still on-going
refactoring / modernization works for ASoC core and drivers, but there
are lots of other changes as well. Here we go, some highlights below:
ASoC:
- Quite a lot of cleanup / refactoring of ASoC core and APIs; most of
them are systematic, but also including cleanups and modernization
- A bulk of updates for some ASoC platforms, Freescale, sunxi and
Intel SST/SOF
- Initial support for Sound Open Firmware on i.MX8
- Removal of deprecated w90x900 and nuc900 drivers
- New support for Cirrus Logic CS47L15 and CS47L92, Freescale i.MX
7ULP and 8MQ, Meson G12A and NXP UDA1334
USB-audio:
- More validations of descriptor units for hardening against bugs
reported by fuzzers
- PCM device assignment workaround for a past call-order change
- Scarlett Gen2 mixer interface, a few more more quirks
HD-audio:
- Support for audio component with AMD/ATI and Nvidia HDMI codecs
- Clean up HD-audio core and remove indirect access ops for Intel SOF
- DMIC detection at probe; it would make systems automatically
falling back to SST/SOF driver on devices that need DMIC handling.
Needs a new Kconfig to set, and beware that it's still new and a
bit experimental
FireWire:
- Lots of code refactoring and cleanups"
* tag 'sound-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (521 commits)
ASoC: sdm845: remove unneeded semicolon
ASoC: fsl_sai: Implement set_bclk_ratio
ASoC: dmaengine: Replace strncpy() with strscpy_pad() for pcm->name
ASoC: wcd9335: remove redundant use of ret variable
ALSA: firewire-tascam: check intermediate state of clock status and retry
ALSA: firewire-tascam: handle error code when getting current source of clock
ASoC: hdmi-codec: Add an op to set callback function for plug event
ASoC: rt5677: keep analog power register at SND_SOC_BIAS_OFF
ASoC: rt5677: Remove magic number register writes
ASoC: soc-core: self contained soc_unbind_aux_dev()
ASoC: soc-core: add soc_unbind_aux_dev()
ASoC: soc-core: self contained soc_bind_aux_dev()
ASoC: soc-core: move soc_probe_link_dais() next to soc_remove_link_dais()
ASoC: soc-core: self contained soc_probe_link_dais()
ASoC: soc-core: add new soc_link_init()
ASoC: soc-core: move soc_probe_dai() next to soc_remove_dai()
ASoC: soc-core: self contained soc_remove_link_dais()
ASoC: soc-core: self contained soc_remove_link_components()
ASoC: soc-core: self contained soc_probe_link_components()
ASoC: rt1308: make array pd static const, makes object smaller
...
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fixup processing of SDIO IRQs during system suspend/resume
- Add helper function to indicate if SDIO IRQs is enabled
MMC host:
- bcm2835: Take SWIOTLB memory size limitation into account
- dw_mmc: Improve SDIO IRQs support
- mtk-sd: Various improvements
- mtk-sd: Improve SDIO IRQs support
- sdhci-iproc: Add support for emmc2 of the BCM2711
- sdhci-of-arasan: Add Support for Intel LGM eMMC
- sdhci-of-aspeed: Add support for the ASPEED SD controller
- sdhci-of-esdhc: Deal with erratum A011334 support in ls1028a 1.0 SoC
- sdhci-pci: Prepare to add support of Genesys Logic GL975x
- sdhci-pci: Add another Id for Intel CML
- sdhci-pci-o2micro: Fix O2 Host data read/write DLL Lock phase shift issue
- sunxi: Add support for H5 compatibles"
* tag 'mmc-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (59 commits)
ms_block: fix spelling mistake "randomally" -> "randomly"
mmc: dw_mmc: hi3798cv200: make array degrees static const, makes object smaller
mmc: sdhci: Convert to use sdio_irq_claimed()
mmc: sdhci: Drop redundant code for SDIO IRQs
mmc: sdhci: Drop redundant check in sdhci_ack_sdio_irq()
mmc: core: Fixup processing of SDIO IRQs during system suspend/resume
mmc: core: WARN if SDIO IRQs are enabled for non-powered card in suspend
mmc: core: Clarify that the ->ack_sdio_irq() callback is mandatory
mmc: core: Clarify sdio_irq_pending flag for MMC_CAP2_SDIO_IRQ_NOTHREAD
mmc: core: Move code to get pending SDIO IRQs to a function
mmc: mtk-sd: Re-store SDIO IRQs mask at system resume
mmc: dw_mmc: Re-store SDIO IRQs mask at system resume
mmc: core: Add helper function to indicate if SDIO IRQs is enabled
mmc: sdhci-pci-o2micro: Fix O2 Host data read/write DLL Lock phase shift issue
mmc: sdhci-pci-o2micro: Move functions in preparation to fix DLL lock phase shift issue
mmc: sdhci-pci-o2micro: Change O2 Host PLL and DLL register name
mmc: sdhci: Fix incorrect switch to HS mode
mmc: sdhci-of-aspeed: Depend on CONFIG_OF_ADDRESS
mmc: sdhci-of-aspeed: Allow max-frequency limitation of SDCLK
mmc: sdhci-of-aspeed: Uphold clocks-on post-condition of set_clock()
...
Pull ia64 updates from Tony Luck:
"The big change here is removal of support for SGI Altix"
* tag 'please-pull-ia64_for_5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux: (33 commits)
genirq: remove the is_affinity_mask_valid hook
ia64: remove CONFIG_SWIOTLB ifdefs
ia64: remove support for machvecs
ia64: move the screen_info setup to common code
ia64: move the ROOT_DEV setup to common code
ia64: rework iommu probing
ia64: remove the unused sn_coherency_id symbol
ia64: remove the SGI UV simulator support
ia64: remove the zx1 swiotlb machvec
ia64: remove CONFIG_ACPI ifdefs
ia64: remove CONFIG_PCI ifdefs
ia64: remove the hpsim platform
ia64: remove now unused machvec indirections
ia64: remove support for the SGI SN2 platform
drivers: remove the SGI SN2 IOC4 base support
drivers: remove the SGI SN2 IOC3 base support
qla2xxx: remove SGI SN2 support
qla1280: remove SGI SN2 support
misc/sgi-xp: remove SGI SN2 support
char/mspec: remove SGI SN2 support
...
The AMD Ryzen gen 3 processors came with a different PCI IDs for the
function 3 & 4 which are used to access the SMN interface. The root
PCI address however remained at the same address as the model 30h.
Adding the F3/F4 PCI IDs respectively to the misc and link ids appear
to be sufficient for k10temp, so let's add them and follow up on the
patch if other functions need more tweaking.
Vicki Pfau sent an identical patch after I checked that no-one had
written this patch. I would have been happy about dropping my patch but
unlike for his patch series, I had already Cc:ed the x86 people and
they already reviewed the changes. Since Vicki has not answered to
any email after his initial series, let's assume she is on vacation
and let's avoid duplication of reviews from the maintainers and merge
my series. To acknowledge Vicki's anteriority, I added her S-o-b to
the patch.
v2, suggested by Guenter Roeck and Brian Woods:
- rename from 71h to 70h
Signed-off-by: Vicki Pfau <vi@endrift.com>
Signed-off-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Tested-by: Marcel Bocu <marcel.p.bocu@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Brian Woods <brian.woods@amd.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci_ids.h
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Cc: "Woods, Brian" <Brian.Woods@amd.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Link: https://lore.kernel.org/r/20190722174510.2179-1-marcel.p.bocu@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
