Some Adreno GPU targets require a special zap shader to bring the GPU
out of secure mode. Define a region to allocate and store the zap
shader.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[bjorn: Rebase ontop of recent reserved-memory patch]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
SDM845 implements ARM's Dynamiq architecture that allows the big and
LITTLE cores to exist in a single cluster sharing the L3 cache.
Fix the cpu-map to put all cpus into a single cluster.
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Specify the relative CPU capacity of all SDM845 AP cores.
The values were provided by Qualcomm engineers.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Andy Gross <agross@kernel.org>
The 8 CPU cores of the SDM845 are organized in two clusters of 4 big
("gold") and 4 little ("silver") cores. Add a cpu-map node to the DT
that describes this topology.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add 'bi_tcxo' as ref clock for the DSI PHYs, it was previously
hardcoded in the PLL 'driver' for the 10nm PHY.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Add the Audio DSP (ADSP) and Compute DSP (CDSP) nodes for TrustZone
based remoteproc, supporting booting these cores on e.g. the MTP, and
enable the same for the MTP.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Define the rmtfs memory node. As the memory region specified in version
10 of the memory map is only 1MB a chunk of unallocated memory is
chosen.
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
Wire up the reset controller in the Qcom UFS controller for the PHY.
This will be used to toggle PHY reset during initialization of the PHY.
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
sdm845 has a total of 21 temperature sensors. Populate DT with
information about them.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <agross@kernel.org>
In order to fix dependencies with rpmpd DT entries, the header was
dropped and hardcoded values were added for opp-level, during the
previous merge window.
Add the header back in now and remove the hardcodings, effectively
reverting commit '08585d21de9875a6064b350957faa0460a4c69a6: arm64: dts:
sdm845: Fixup dependency on RPMPD includes'
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Include the device tree header for the on-chip interconnect endpoint
resources on sdm845 devices. This will allow using the "interconnects"
property in DT nodes to describe the interconnect path resources they use.
The sdm845 interconnect provider DT node is already present, but the
header file with the resources is not included, so let's fix this.
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes a dependency issue with the RPMPD dt bindings. This
temporarily removes the include file and adds hardcoded values for the
OPPs until the other changes full land. This will be addressed in 5.2.
Fixes: 5b6f186f0a ("arm64: dts: sdm845: Add rpmh powercontroller node")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
When commit 022bccb840 ("dts: arm64/sdm845: Add WCN3990 WLAN module
device node") was posted upstream no clocks were specified. However,
when the pack was picked into the Chrome OS kernel tree (allegedly
directly from the mailing list post) it had clock properties.
I presume that the clock should be there, so let's add it.
Fixes: 022bccb840 ("dts: arm64/sdm845: Add WCN3990 WLAN module device node")
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add also the required iommus property]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The USB controllers need to be associated with their respective IOMMU
bank, so define this on the dwc3 nodes.
Also add dma-ranges to the qcom-dwc3 nodes to make the bus' DMA mask
propagate to the dwc3 controller instances.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
With apps_smmu initializing the SMMU we must specify iommus property for
the sdhc controller.
Fixes: 4429e57567 ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since all cpus in the big and little clusters, respectively, are in the
same frequency domain, use all of them for mitigation in the
cooling-map. We end up with two cooling devices - one each for the big
and little clusters.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add RSC (Resource State Coordinator) provider
dictating network-on-chip interconnect bus performance
found on SDM845-based platforms.
Signed-off-by: David Dai <daidavid1@codeaurora.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
For devices attached to an IOMMU, translation between IOVA and physical
addresses is no longer 1:1 and dma-ranges should be specified to
describe the available IOVA address space.
On SDM845 the busses are implemented with 36 address bits, so dma-ranges
must be defined to reduce the size of the IOVA address space from the 48
bits supported by the SMMU. Without this DMA allocations may end up with
IOVAs outside the valid range, that gets truncated by the bus between
the device and its translation unit.
Also extend ranges to describe the available address space.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The busses on SDM845 provides 36 address bits, extend the address and
size cells to make it possible to describe this in "ranges" and
"dma-ranges".
While touching all reg properties, addresses are padded to 8 digits.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Correct address for pcs_misc register region of USB3 QMP UNI PHY.
These registers are used during runtime-suspend/resume routines
of phy.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Fixes: ca4db2b538 ("arm64: dts: qcom: sdm845: Add USB-related nodes")
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the low pass audio clock controller node to sdm845 based on
the example in the bindings.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[bjorn: Disabled lpasscc node, as it's normally protected]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the Quad SPI controller to the main sdm845 device tree file.
Boards will be expected to assign the proper pinctrl depending on how
many chip selects they have hooked up and how many data lines.
This depends on commit 48735597f7 ("clk: qcom: Add qspi (Quad SPI)
clock defines for sdm845 to header") to add the needed defines. It
also shouldn't land until the patch ("dt-bindings: spi: Qualcomm Quad
SPI(QSPI) documentation") [1] lands.
[1] https://lkml.kernel.org/r/20181002214709.162330-1-ryandcase@chromium.org
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
DPU is short for the Display Processing Unit. It is the display
controller on Qualcomm SDM845 chips.
This change adds MDSS and DSI nodes to enable display on the
target device.
Changes in v2:
- Beefed up commit message
- Use SoC specific compatibles for mdss and dpu (Rob H)
- Use assigned-clocks to set initial clock frequency(Rob H)
Changes in v3:
- added IOMMU node
- Fix device naming (remove _phys)
- Use correct IRQ_TYPE in interrupt specifiers
Changes in v4:
- move mdss node to preserve the unit address sort order
- remove _clk suffix from dsi clocks
(both the comments are from Doug Anderson)
Changes in v5:
- Keep the device status "disabled" by default (Bjorn Andersson)
- Use MDSS_GDSC macro (Jordan)
- Fix phy-names (Jordan)
- List reg ranges in numerical order (Jordan)
Changes in v6:
- Separating this patch out of the series
- fix phy-names
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the second lane registers for the USB PHY, now that the
QMP phy bindings have been updated. This way the driver can stop
reaching beyond its register region to get at the second lane.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add device node for arm,mmu-500 available on sdm845.
This MMU-500 with single TCU and multiple TBU architecture
is shared among all the peripherals except gpu.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds nodes for all possible UARTs to sdm845.dtsi. By default
only configure the RX/TX lines with pinctrl. Boards that use UARTs
with flow control can overwrite the configuration in the
<board>.dtsi.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
RNG hardware in SDM845 features (Execution Environment) EE for
HLOS to use, add the node for prng-ee for sdm845.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the display clock controller node to sdm845 based on the
examples in the bindings.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the node to support AOSS reset driver on
SDM845
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
[bjorn: Updated addresses to match the binding that was merged]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
