Merge tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB patches from Greg KH:
 "Here's the big USB pull request for 3.15-rc1.

  The normal set of patches, lots of controller driver updates, and a
  smattering of individual USB driver updates as well.

  All have been in linux-next for a while"

* tag 'usb-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (249 commits)
  xhci: Transition maintainership to Mathias Nyman.
  USB: disable reset-resume when USB_QUIRK_RESET is set
  USB: unbind all interfaces before rebinding any
  usb: phy: Add ulpi IDs for SMSC USB3320 and TI TUSB1210
  usb: gadget: tcm_usb_gadget: stop format strings
  usb: gadget: f_fs: add missing spinlock and mutex unlock
  usb: gadget: composite: switch over to ERR_CAST()
  usb: gadget: inode: switch over to memdup_user()
  usb: gadget: f_subset: switch over to PTR_RET
  usb: gadget: lpc32xx_udc: fix wrong clk_put() sequence
  USB: keyspan: remove dead debugging code
  USB: serial: add missing newlines to dev_<level> messages.
  USB: serial: add missing braces
  USB: serial: continue to write on errors
  USB: serial: continue to read on errors
  USB: serial: make bulk_out_size a lower limit
  USB: cypress_m8: fix potential scheduling while atomic
  devicetree: bindings: document lsi,zevio-usb
  usb: chipidea: add support for USB OTG controller on LSI Zevio SoCs
  usb: chipidea: imx: Use dev_name() for ci_hdrc name to distinguish USBs
  ...

drivers/usb/core/hub.c

@@ -141,19 +141,27 @@ static int usb_device_supports_lpm(struct usb_device *udev)
 		return 0;
 	}
 
-	/* All USB 3.0 must support LPM, but we need their max exit latency
-	 * information from the SuperSpeed Extended Capabilities BOS descriptor.
+	/*
+	 * According to the USB 3.0 spec, all USB 3.0 devices must support LPM.
+	 * However, there are some that don't, and they set the U1/U2 exit
+	 * latencies to zero.
 	 */
 	if (!udev->bos->ss_cap) {
-		dev_warn(&udev->dev, "No LPM exit latency info found.  "
-				"Power management will be impacted.\n");
+		dev_info(&udev->dev, "No LPM exit latency info found, disabling LPM.\n");
 		return 0;
 	}
-	if (udev->parent->lpm_capable)
-		return 1;
 
-	dev_warn(&udev->dev, "Parent hub missing LPM exit latency info.  "
-			"Power management will be impacted.\n");
+	if (udev->bos->ss_cap->bU1devExitLat == 0 &&
+			udev->bos->ss_cap->bU2DevExitLat == 0) {
+		if (udev->parent)
+			dev_info(&udev->dev, "LPM exit latency is zeroed, disabling LPM.\n");
+		else
+			dev_info(&udev->dev, "We don't know the algorithms for LPM for this host, disabling LPM.\n");
+		return 0;
+	}
+
+	if (!udev->parent || udev->parent->lpm_capable)
+		return 1;
 	return 0;
 }
 
@@ -499,7 +507,8 @@ static void led_work (struct work_struct *work)
 		changed++;
 	}
 	if (changed)
-		schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD);
+		queue_delayed_work(system_power_efficient_wq,
+				&hub->leds, LED_CYCLE_PERIOD);
 }
 
 /* use a short timeout for hub/port status fetches */
@@ -1041,7 +1050,8 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 		if (type == HUB_INIT) {
 			delay = hub_power_on(hub, false);
 			INIT_DELAYED_WORK(&hub->init_work, hub_init_func2);
-			schedule_delayed_work(&hub->init_work,
+			queue_delayed_work(system_power_efficient_wq,
+					&hub->init_work,
 					msecs_to_jiffies(delay));
 
 			/* Suppress autosuspend until init is done */
@@ -1195,7 +1205,8 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 		/* Don't do a long sleep inside a workqueue routine */
 		if (type == HUB_INIT2) {
 			INIT_DELAYED_WORK(&hub->init_work, hub_init_func3);
-			schedule_delayed_work(&hub->init_work,
+			queue_delayed_work(system_power_efficient_wq,
+					&hub->init_work,
 					msecs_to_jiffies(delay));
 			return;		/* Continues at init3: below */
 		} else {
@@ -1209,7 +1220,8 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
 	if (status < 0)
 		dev_err(hub->intfdev, "activate --> %d\n", status);
 	if (hub->has_indicators && blinkenlights)
-		schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD);
+		queue_delayed_work(system_power_efficient_wq,
+				&hub->leds, LED_CYCLE_PERIOD);
 
 	/* Scan all ports that need attention */
 	kick_khubd(hub);
@@ -3095,9 +3107,19 @@ static int finish_port_resume(struct usb_device *udev)
 	 * operation is carried out here, after the port has been
 	 * resumed.
 	 */
-	if (udev->reset_resume)
+	if (udev->reset_resume) {
+		/*
+		 * If the device morphs or switches modes when it is reset,
+		 * we don't want to perform a reset-resume.  We'll fail the
+		 * resume, which will cause a logical disconnect, and then
+		 * the device will be rediscovered.
+		 */
  retry_reset_resume:
-		status = usb_reset_and_verify_device(udev);
+		if (udev->quirks & USB_QUIRK_RESET)
+			status = -ENODEV;
+		else
+			status = usb_reset_and_verify_device(udev);
+	}
 
 	/* 10.5.4.5 says be sure devices in the tree are still there.
 	 * For now let's assume the device didn't go crazy on resume,
@@ -3960,7 +3982,7 @@ static void hub_set_initial_usb2_lpm_policy(struct usb_device *udev)
 	connect_type = usb_get_hub_port_connect_type(udev->parent,
 			udev->portnum);
 
-	if ((udev->bos->ext_cap->bmAttributes & USB_BESL_SUPPORT) ||
+	if ((udev->bos->ext_cap->bmAttributes & cpu_to_le32(USB_BESL_SUPPORT)) ||
 			connect_type == USB_PORT_CONNECT_TYPE_HARD_WIRED) {
 		udev->usb2_hw_lpm_allowed = 1;
 		usb_set_usb2_hardware_lpm(udev, 1);
@@ -4109,8 +4131,12 @@ hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1,
 
 			did_new_scheme = true;
 			retval = hub_enable_device(udev);
-			if (retval < 0)
+			if (retval < 0) {
+				dev_err(&udev->dev,
+					"hub failed to enable device, error %d\n",
+					retval);
 				goto fail;
+			}
 
 #define GET_DESCRIPTOR_BUFSIZE	64
 			buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO);
@@ -4313,7 +4339,8 @@ check_highspeed (struct usb_hub *hub, struct usb_device *udev, int port1)
 		/* hub LEDs are probably harder to miss than syslog */
 		if (hub->has_indicators) {
 			hub->indicator[port1-1] = INDICATOR_GREEN_BLINK;
-			schedule_delayed_work (&hub->leds, 0);
+			queue_delayed_work(system_power_efficient_wq,
+					&hub->leds, 0);
 		}
 	}
 	kfree(qual);
@@ -4542,7 +4569,9 @@ static void hub_port_connect_change(struct usb_hub *hub, int port1,
 				if (hub->has_indicators) {
 					hub->indicator[port1-1] =
 						INDICATOR_AMBER_BLINK;
-					schedule_delayed_work (&hub->leds, 0);
+					queue_delayed_work(
+						system_power_efficient_wq,
+						&hub->leds, 0);
 				}
 				status = -ENOTCONN;	/* Don't retry */
 				goto loop_disable;
@@ -4741,6 +4770,8 @@ static void hub_events(void)
 
 		/* deal with port status changes */
 		for (i = 1; i <= hdev->maxchild; i++) {
+			struct usb_device *udev = hub->ports[i - 1]->child;
+
 			if (test_bit(i, hub->busy_bits))
 				continue;
 			connect_change = test_bit(i, hub->change_bits);
@@ -4839,8 +4870,6 @@ static void hub_events(void)
 			 */
 			if (hub_port_warm_reset_required(hub, portstatus)) {
 				int status;
-				struct usb_device *udev =
-					hub->ports[i - 1]->child;
 
 				dev_dbg(hub_dev, "warm reset port %d\n", i);
 				if (!udev ||
@@ -4857,6 +4886,24 @@ static void hub_events(void)
 					usb_unlock_device(udev);
 					connect_change = 0;
 				}
+			/*
+			 * On disconnect USB3 protocol ports transit from U0 to
+			 * SS.Inactive to Rx.Detect. If this happens a warm-
+			 * reset is not needed, but a (re)connect may happen
+			 * before khubd runs and sees the disconnect, and the
+			 * device may be an unknown state.
+			 *
+			 * If the port went through SS.Inactive without khubd
+			 * seeing it the C_LINK_STATE change flag will be set,
+			 * and we reset the dev to put it in a known state.
+			 */
+			} else if (udev && hub_is_superspeed(hub->hdev) &&
+				   (portchange & USB_PORT_STAT_C_LINK_STATE) &&
+				   (portstatus & USB_PORT_STAT_CONNECTION)) {
+				usb_lock_device(udev);
+				usb_reset_device(udev);
+				usb_unlock_device(udev);
+				connect_change = 0;
 			}
 
 			if (connect_change)
@@ -5114,7 +5161,7 @@ static int usb_reset_and_verify_device(struct usb_device *udev)
 	struct usb_hcd			*hcd = bus_to_hcd(udev->bus);
 	struct usb_device_descriptor	descriptor = udev->descriptor;
 	struct usb_host_bos		*bos;
-	int 				i, ret = 0;
+	int				i, j, ret = 0;
 	int				port1 = udev->portnum;
 
 	if (udev->state == USB_STATE_NOTATTACHED ||
@@ -5240,6 +5287,9 @@ static int usb_reset_and_verify_device(struct usb_device *udev)
 				ret);
 			goto re_enumerate;
 		}
+		/* Resetting also frees any allocated streams */
+		for (j = 0; j < intf->cur_altsetting->desc.bNumEndpoints; j++)
+			intf->cur_altsetting->endpoint[j].streams = 0;
 	}
 
 done:
@@ -5342,10 +5392,11 @@ int usb_reset_device(struct usb_device *udev)
 				else if (cintf->condition ==
 						USB_INTERFACE_BOUND)
 					rebind = 1;
+				if (rebind)
+					cintf->needs_binding = 1;
 			}
-			if (ret == 0 && rebind)
-				usb_rebind_intf(cintf);
 		}
+		usb_unbind_and_rebind_marked_interfaces(udev);
 	}
 
 	usb_autosuspend_device(udev);